- 您現在的位置：買賣IC網 > PDF目錄368355 > PTH12030W Universal Input Linear Fluorescent Ballast using the IR2167 PDF資料下載
參數資料
| 型號： | PTH12030W |
| 英文描述： | Universal Input Linear Fluorescent Ballast using the IR2167 |
| 中文描述： | 26答：12 - V輸入寬輸出調節插入電源模塊 |
| 文件頁數： | 2/8頁 |
| 文件大?。?/td> | 171K |
| 代理商： | PTH12030W |
For technical support and more information, see inside back cover or visit www.ti.com
A
Pin Descriptions
Vin:
The positive input voltage power node to the mod-
ule, which is referenced to common GND.
GND:
This is the common ground connection for the
‘V
in
’ and ‘V
out
’ power connections. It is also the 0 VDC
reference for the ‘Inhibit’ and ‘V
o
Adjust’ control inputs.
Vout:
The regulated positive power output with respect
to the GND node.
Inhibit:
The Inhibit pin is an open-collector/drain negative
logic input that is referenced to GND. Applying a low-
level ground signal to this input disables the module’s
output and turns off the output voltage. When the Inhibit
control is active, the input current drawn by the regulator
is significantly reduced. If the Inhibit pin is left open-
circuit, the module will produce an output whenever a
valid input source is applied.
Vo Adjust:
A 0.5 %, 0.1 W resistor must be connected
between this pin and the GND pin to set the output
voltage to the desired value. The set point range for the
output voltage is from 1.2 V to 5.5 V. The resistor required
for a given output voltage may be calculated from the
following formula. If left open circuit, the module out-
put will default to its lowest output voltage value. For
further information on the adjustment and/or trimming
of the output voltage, consult the related application note.
R
set
= 10 k · V
out
– 1.2 V
– 1.82 k
The specification table gives the preferred resistor values
for a number of standard output voltages.
Ordering Information
Output Voltage
(PTH12000 xx)
Code
Voltage
W
1.2 V – 5.5 V
Package Options
(PTH12000x
Code
Description
AH
Horiz. T/H
AS
SMD, Standard
(3)
)
(1)
Pkg Ref.
(2)
(EUS)
(EUT)
(Adjust)
Notes:
(1) Add “T” to end of part number for tape and reel on SMD packages only.
(2) Reference the applicable package reference drawing for the dimensions and PC board layout
(3) “Standard” option specifies 63/37, Sn/Pb pin solder material.
6-A, 12-V Input Non-Isolated
Wide-Output Adjust Power Module
SLTS202A
–
MAY 2003
–
REVISED MAY 2003
PTH12000 Series
—
12-V Input
相關PDF資料 |
PDF描述 |
|---|---|
| PTH8C16TBB101M | Universal Input Linear Fluorescent Ballast using the IR2166 |
| PTH8C16TBB221M | Mini-ballast for single 25W compact fluorescent ballast, European version with 230VACin |
| PTH8C16TBB330M | Intelligent Power Switch 1 Channel Low Side Driver in a SOT-223 Package |
| PTH8C16TBB470M | Intelligent Power Switch 1 Channel Low Side Driver in a TO-220AB Package |
| PTH8C16TBB481M | Intelligent Power Switch 1 Channel Low Side Driver in a SOT-223 Package |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PTH12030WAD | 功能描述:DC/DC轉換器 1.2 to 5.5V 26A 12V Input WideAdj Module RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
| PTH12030WADT | 制造商:EMERSON-NETWORKPOWER 制造商全稱:Emerson Network Power 功能描述:DC-DC CONVERTERS |
| PTH12030WAH | 功能描述:DC/DC轉換器 1.2 to 5.5V 26A 12V Input WideAdj Module RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
| PTH12030WAH | 制造商:POWER TRENDS 功能描述:IC DC/DC 12VIN 26A ADJ O/P 12030 |
| PTH12030WAHT | 制造商:EMERSON-NETWORKPOWER 制造商全稱:Emerson Network Power 功能描述:DC-DC CONVERTERS |
發布緊急采購，3分鐘左右您將得到回復。