- 您現在的位置：買賣IC網 > PDF目錄69255 > PTH12020LAZT (TEXAS INSTRUMENTS INC) 1-OUTPUT DC-DC REG PWR SUPPLY MODULE PDF資料下載
參數資料
| 型號： | PTH12020LAZT |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 電源模塊 |
| 英文描述： | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| 封裝： | ROHS COMPLIANT |
| 文件頁數： | 6/27頁 |
| 文件大?。?/td> | 930K |
| 代理商： | PTH12020LAZT |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁
POWER-UP INTO A NON-PREBIASED OUTPUT — AUTO-TRACK FUNCTION
UDG06074
RSET
2 k
0.1 W
1 %
CO
330
F
CI
560
F
2
8
1
7
3
9
10
PTH12060W
4
6
+
GND
L
O
A
D
Q1
BSS138
1=TurnOff
+
Margin
Down
Margin
Up
Inhibit
Track
GND
VoAdj
5
VO
VOSense
VI
SLTS208I – MAY 2003 – REVISED MARCH 2009 ............................................................................................................................................................. www.ti.com
The Auto-Track function is unique to the PTH/PTV family, and is available with all POLA products. Auto-Track
was designed to simplify the amount of circuitry required to make the output voltage from each module power up
and power down in sequence. The sequencing of two or more supply voltages during power up is a common
requirement for complex mixed-signal applications that use dual-voltage VLSI ICs such as the TMS320 DSP
family, microprocessors, and ASICs.
Basic Power-Up using Auto-Track
For applications requiring output voltage on/off control, each series of the PTH family incorporates the track
control pin. The Auto-Track feature should be used instead of the inhibit feature wherever there is a requirement
for the output voltage from the regulator to be turned on/off.
Figure 12 shows the typical application for basic start-up. Note the discrete transistor (Q1). The track input has
its own internal pull-up to a potential of 5 V to 13.2 V The input is not compatible with TTL logic devices. An
open-collector (or open-drain) discrete transistor or supply voltage supervisor (TPS3808 or TPS7712) is
recommended for control.
Figure 12. Basic Start-up Control Circuit
Turning on Q1 applies a low voltage to the track control pin and disables the output of the module. If Q1 is then
turned off, the output ramps immediately to the regulated output voltage. A regulated output voltage is produced
within 35 ms. With the initial application of the input source voltage, the track pin must be held low (Q1 turned
ON) for at least 40 ms. Figure 13 shows the typical rise in both the output voltage and input current, following the
turn off of Q1. The turn off of Q1 corresponds to the rise in the waveform, Q1 Vds. The waveforms were
measured with a 10-A constant current load.
14
Copyright 2003–2009, Texas Instruments Incorporated
Product Folder Link(s) :PTH12020W/L
相關PDF資料 |
PDF描述 |
|---|---|
| PTH12020WAZ | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| PTH12020WAS | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| PTH12020WAD | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| PTH12020WAH | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| PTH12020WAST | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PTH12020W | 制造商:TI 制造商全稱:Texas Instruments 功能描述:18-A, 12-V INPUT NON-ISOLATED WIDE-OUTPUT ADJUST POWER MODULE |
| PTH12020WAD | 功能描述:DC/DC轉換器 10.8-13.2Vin 5.5V18A 1.495" x0.870"x0.354 RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
| PTH12020WADT | 制造商:EMERSON-NETWORKPOWER 制造商全稱:Emerson Network Power 功能描述:DC-DC CONVERTERS |
| PTH12020WAH | 功能描述:DC/DC轉換器 1.2 to 5.5V 18A 12V Input WideAdj Module RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
| PTH12020WAH | 制造商:POWER TRENDS 功能描述:IC DC/DC 12VIN 18A ADJ O/P 12020 |
發(fā)布緊急采購，3分鐘左右您將得到回復。