- 您現在的位置：買賣IC網 > PDF目錄69254 > PTH08T230WAZT (TEXAS INSTRUMENTS INC) 1-OUTPUT DC-DC REG PWR SUPPLY MODULE PDF資料下載
參數資料
| 型號： | PTH08T230WAZT |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 電源模塊 |
| 英文描述： | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| 封裝： | ROHS COMPLIANT PACKAGE-10 |
| 文件頁數： | 17/39頁 |
| 文件大?。?/td> | 1281K |
| 代理商： | PTH08T230WAZT |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁
t-Time=4ms/div
I (2 A/div)
I
V (5V/div)
I
V
(2V/div)
O
PTH08T230W
Track
GND
3
2
C
I
V
I
V
I
SLTS265K – NOVEMBER 2005 – REVISED JUNE 2010
www.ti.com
Soft-Start Power Up
The Auto-Track feature allows the power-up of multiple PTH/PTV modules to be directly controlled from the
Track pin. However in a stand-alone configuration, or when the Auto-Track feature is not being used, the Track
Figure 20. Defeating the Auto-Track Function
Figure 21. Power-Up Waveform
When the Track pin is connected to the input voltage the Auto-Track function is permanently disengaged. This
allows the module to power up entirely under the control of its internal soft-start circuitry. When power up is
under soft-start control, the output voltage rises to the set-point at a quicker and more linear rate. From the
moment a valid input voltage is applied, the soft-start control introduces a short time delay (typically 2 ms–10 ms)
before allowing the output voltage to rise. The output then progressively rises to the module’s setpoint voltage.
Figure 21 shows the soft-start power-up characteristic of the PTH08T230W operating from a 12-V input bus and
configured for a 3.3-V output. The waveforms were measured with a 6-A constant current load and the
Auto-Track feature disabled. The initial rise in input current when the input voltage first starts to rise is the charge
current drawn by the input capacitors. Power-up is complete within 20 ms.
Overcurrent Protection
For protection against load faults, all modules incorporate output overcurrent protection. Applying a load that
exceeds the regulator's overcurrent threshold causes the regulated output to shut down. Following shutdown, a
module periodically attempts to recover by initiating a soft-start power-up. This is described as a hiccup mode of
operation, whereby the module continues in a cycle of successive shutdown and power up until the load fault is
removed. During this period, the average current flowing into the fault is significantly reduced. Once the fault is
removed, the module automatically recovers and returns to normal operation.
Overtemperature Protection (OTP)
A thermal shutdown mechanism protects the module’s internal circuitry against excessively high temperatures. A
rise in the internal temperature may be the result of a drop in airflow, or a high ambient temperature. If the
internal temperature exceeds the OTP threshold, the module’s Inhibit control is internally pulled low. This turns
the output off. The output voltage drops as the external output capacitors are discharged by the load circuit. The
recovery is automatic, and begins with a soft-start power up. It occurs when the sensed temperature decreases
by about 10°C below the trip point.
The overtemperature protection is a last resort mechanism to prevent thermal stress to the regulator.
Operation at or close to the thermal shutdown temperature is not recommended and reduces the long-term
reliability of the module. Always operate the regulator within the specified safe operating area (SOA) limits for
the worst-case conditions of ambient temperature and airflow.
24
Copyright 2005–2010, Texas Instruments Incorporated
Product Folder Link(s): PTH08T230W PTH08T231W
相關PDF資料 |
PDF描述 |
|---|---|
| PTH08T230WAZ | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| PTH08T231WAZ | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| PTH08T230WAST | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| PTH08T230WAS | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| PTH08T230WAD | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PTH08T231W | 制造商:TI 制造商全稱:Texas Instruments 功能描述:6-A, 4.5-V to 14-V INPUT, NON-ISOLATED, WIDE-OUTPUT, ADJUSTABLE POWER MODULE WITH TurboTrans⑩ |
| PTH08T231WAD | 功能描述:DC/DC轉換器 6A 4.5V-14Vin Cer Cap Adj Pwr Module RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
| PTH08T231WAS | 功能描述:DC/DC轉換器 6A 4.5V-14Vin Cer Cap Adj Pwr Module RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
| PTH08T231WAST | 功能描述:DC/DC轉換器 6A 4.5V-14Vin Cer Cap Adj Pwr Module RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
| PTH08T231WAZ | 功能描述:DC/DC轉換器 6-A 4.5V-14V Input Cer Cap Ver Non-Iso RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
發布緊急采購，3分鐘左右您將得到回復。