參數資料
型號: PTH05010WAST
廠商: TEXAS INSTRUMENTS INC
元件分類: 電源模塊
英文描述: 1-OUTPUT DC-DC REG PWR SUPPLY MODULE
封裝: DIP-10
文件頁數: 13/19頁
文件大?。?/td> 513K
代理商: PTH05010WAST
For technical support and more information, visit http://power.ti.com
Environmental & Absolute Maximum Ratings (Voltages are with respect to GND)
Characteristics
Symbols
Conditions
Min
Typ
Max
Units
Track Input Voltage
Vtrack
–0.3
Vin + 0.3
V
Operating Temperature Range
Ta
Over Vin Range
–40
85
°C
Solder Reflow Temperature
Treflow
Surface temperature of module body or pins
235 (i)
°C
Storage Temperature
Ts
–40
125
°C
Mechanical Shock
Per Mil-STD-883D, Method 2002.3
500
G’s
1 msec, Sine, mounted
Mechanical Vibration
Mil-STD-883D, Method 2007.2
Suffix H
20
G’s
20-2000 Hz
Suffix S
15
Weight
5
grams
Flammability
Meets UL 94V-O
Notes:
(i) During reflow of SMD package version do not elevate peak temperature of the module, pins or internal components above the stated maximum.
15-A, 5-V Input Non-Isolated
Wide-Output Adjust Power Module
SLTS204C – MAY 2003 – REVISED DECEMBER 2003
PTH05010 W —5-V Input
Specifications (Unless otherwise stated, Ta =25 °C, Vin =5 V, Vo =3.3 V, Cin =470 F, Cout =0 F, and Io =Iomax)
PTH05010W
Characteristics
Symbols
Conditions
Min
Typ
Max
Units
Output Current
Io
0.8 V
≤ Vo ≤ 3.6 V
60 °C, 200 LFM airflow
0
15 (1)
A
25 °C, natural convection
0
15 (1)
Input Voltage Range
Vin
Over Io range
4.5
5.5
V
Set-Point Voltage Tolerance
Votol
±2 (2)
%Vo
Temperature Variation
Regtemp
–40 °C <Ta < +85 °C
±0.5
%Vo
Line Regulation
Regline
Over Vin range
±10
mV
Load Regulation
Regload
Over Io range
±12
mV
Total Output Variation
Regtot
Includes set-point, line, load,
±3 (2)
%Vo
–40 °C
≤ Ta ≤ +85 °C
Efficiency
η
Io =10 A
RSET = 698
Vo = 3.3 V
95
RSET = 2.21 k Vo = 2.5 V
93
RSET = 5.49 k Vo = 1.8 V
91
%
RSET = 8.87 k Vo = 1.5 V
90
RSET = 17.4 k Vo = 1.2 V
88
RSET = 36.5 k Vo = 1.0 V
86—
Vo Ripple (pk-pk)
Vr
20 MHz bandwidth
30
mVpp
Over-Current Threshold
Io trip
Reset, followed by auto-recovery
27.5
A
Transient Response
1 A/s load step, 50 to 100 % Iomax,
Cout =330 F
ttr
Recovery Time
70
Sec
Vtr
Vo over/undershoot
100
mV
Margin Up/Down Adjust
Vomargin
± 5
%
Margin Input Current (pins 9 /10)
IIL margin
Pin to GND
– 8 (3)
—A
Track Input Current (pin 8)
IIL track
Pin to GND
–130 (4)
A
Track Slew Rate Capability
dVtrack/dt
Cout ≤ Cout(max)
1
V/ms
Under-Voltage Lockout
UVLO
Vin increasing
4.3
4.45
V
Vin decreasing
3.4
3.7
Inhibit Control (pin3)
Referenced to GND
Input High Voltage
VIH
Vin –0.5
Open (4)
V
Input Low Voltage
VIL
–0.2
0.8
Input Low Current
IIL inhibit
Pin to GND
–130
A
Input Standby Current
Iin inh
Inhibit (pin 3) to GND, Track (pin 8) open
10
mA
Switching Frequency
s
Over Vin and Io ranges
275
300
325
kHz
External Input Capacitance
Cin
470 (5)
——F
External Output Capacitance
Cout
Capacitance value
non-ceramic
0
330 (6)
8,250 (7)
F
ceramic
0
300
Equiv. series resistance (non-ceramic)
4
(8)
——m
Reliability
MTBF
Per Bellcore TR-332
5.7
106 Hrs
50 % stress, Ta =40 °C, ground benign
Notes: (1) See SOA curves or consult factory for appropriate derating.
(2) The set-point voltage tolerance is affected by the tolerance and stability ofRSET. The stated limit is unconditionally met if RSET has a tolerance of 1 %
with 200 ppm/°C or better temperature stability.
(3) A small low-leakage (<100 nA) MOSFET is recommended to control this pin. The open-circuit voltage is less than 1 Vdc.
(4) This control pin has an internal pull-up to the input voltage Vin. If it is left open-circuit the module will operate when input power is applied. A small
low-leakage (<100 nA) MOSFET is recommended for control. For further information, consult the related application note.
(5) A 470 F electrolytic input capacitor is required for proper operation. The capacitor must be rated for a minimum of 700 mA rms of ripple current.
(6) An external output capacitor is not required for basic operation. Adding 330 F of distributed capacitance at the load will improve the transient response.
(7) This is the calculated maximum. The minimum ESR limitation will often result in a lower value. Consult the application notes for further guidance.
(8) This is the typical ESR for all the electrolytic (non-ceramic) ouput capacitance. Use 7 m
as the minimum when using max-ESR values to calculate.
相關PDF資料
PDF描述
PTH05010YAS 1-OUTPUT DC-DC REG PWR SUPPLY MODULE
PTH03010YAS 1-OUTPUT DC-DC REG PWR SUPPLY MODULE
PTH05010YAST 1-OUTPUT DC-DC REG PWR SUPPLY MODULE
PTH12010YAZ 1-OUTPUT DC-DC REG PWR SUPPLY MODULE
PTH03010YAST 1-OUTPUT DC-DC REG PWR SUPPLY MODULE
相關代理商/技術參數
參數描述
PTH05010WAZ 功能描述:DC/DC轉換器 15A 5V-In Wide-Out Adj Plug-in Pwr Mdl RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓(標稱): 輸出端數量:1 輸出電壓(通道 1):3.3 V 輸出電流(通道 1):600 mA 輸出電壓(通道 2): 輸出電流(通道 2): 安裝風格:SMD/SMT 封裝 / 箱體尺寸:
PTH05010WAZT 功能描述:DC/DC轉換器 4.5-5.5Vin 0.8-3.6V 1.370" x0.620"x0.354 RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓(標稱): 輸出端數量:1 輸出電壓(通道 1):3.3 V 輸出電流(通道 1):600 mA 輸出電壓(通道 2): 輸出電流(通道 2): 安裝風格:SMD/SMT 封裝 / 箱體尺寸:
PTH05010Y 制造商:TI 制造商全稱:Texas Instruments 功能描述:15-A NON-ISOLATED DDR/QDR MEMORY BUS TERMINATION MODULES
PTH05010YAD 功能描述:DC/DC轉換器 27W 5VDC .55-1.8V Through-Hole RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓(標稱): 輸出端數量:1 輸出電壓(通道 1):3.3 V 輸出電流(通道 1):600 mA 輸出電壓(通道 2): 輸出電流(通道 2): 安裝風格:SMD/SMT 封裝 / 箱體尺寸:
PTH05010YADT 制造商:EMERSON-NETWORKPOWER 制造商全稱:Emerson Network Power 功能描述:DC-DC CONVERTERS