參數資料
型號: PTH03050WAD
廠商: TEXAS INSTRUMENTS INC
元件分類: 電源模塊
英文描述: 1-OUTPUT DC-DC REG PWR SUPPLY MODULE
封裝: ROHS COMPLIANT, DIP-6
文件頁數: 4/19頁
文件大小: 590K
代理商: PTH03050WAD
Application Notes
For technical support and further information visit http://power.ti.com
PTH/PTV Series of Wide-Output Adjust
Power Modules (3.3/5-V Input)
Margin Up/Down Controls
The PTHxx060, PTHxx010, PTHxx020, and PTHxx030
products incorporate Margin Up and Margin Down con-
trol inputs. These controls allow the output voltage to be
momentarily adjusted 1, either up or down, by a nominal
5%. This provides a convenient method for dynamically
testing the operation of the load circuit over its supply
margin or range. It can also be used to verify the function
of supply voltage supervisors. The ±5% change is applied
to the adjusted output voltage, as set by the external resis-
tor, Rset at the Vo Adjust pin.
The 5% adjustment is made by pulling the appropriate
margin control input directly to the GND terminal 2.
A low-leakage open-drain device, such as an n-channel
MOSFET or p-channel JFET is recommended for this
purpose 3. Adjustments of less than 5% can also be accom-
modated by adding series resistors to the control inputs.
The value of the resistor can be selected from Table 3-2,
or calculated using the following formula.
Up/Down Adjust Resistance Calculation
To reduce the margin adjustment to a value less than 5%,
series resistors are required (See RD and RU in Figure 3-8).
For the same amount of adjustment, the resistor value
calculated for RU and RD will be the same. The formulas
is as follows.
R
U or RD =
499
– 99.8
k
%
Where
% = The desired amount of margin adjust in
percent.
Notes:
1. The Margin Up* and Margin Dn* controls were not
intended to be activated simultaneously. If they are
their affects on the output voltage may not completely
cancel, resulting in the possibility of a slightly higher
error in the output voltage set point.
2. The ground reference should be a direct connection to
the module GND at pin 7 (pin 1 for the PTHxx050).
This will produce a more accurate adjustment at the
load circuit terminals. The transistors Q1 and Q2 should
be located close to the regulator.
3. The Margin Up and Margin Dn control inputs are not
compatible with devices that source voltage. This includes
TTL logic. These are analog inputs and should only be
controlled with a true open-drain device (preferably
a discrete MOSFET transistor). The device selected
should have low off-state leakage current. Each input
sources 8 A when grounded, and has an open-circuit
voltage of 0.8 V.
Figure 3–8; Margin Up/Down Application Schematic
Table 3-2; Margin Up/Down Resistor Values
% Adjust
RU / RD
5
0.0 k
4
24.9 k
3
66.5 k
2
150.0 k
1
397.0 k
C
out
+
C
in
V
IN
GND
MargDn
L
O
A
D
Q
2
+V
OUT
Q
1
+
MargUp
0V
+V
o
R
D
R
U
PTH05010W
(Top View)
1
2
10
9
8
7
6
5
4
3
GND
R
SET
0.1 W, 1 %
相關PDF資料
PDF描述
PTH03050WAST 1-OUTPUT DC-DC REG PWR SUPPLY MODULE
PTH03050WAS 1-OUTPUT DC-DC REG PWR SUPPLY MODULE
PTH03050WAH 1-OUTPUT DC-DC REG PWR SUPPLY MODULE
PTH04000WAH 1-OUTPUT DC-DC REG PWR SUPPLY MODULE
PTH04000WAST 1-OUTPUT DC-DC REG PWR SUPPLY MODULE
相關代理商/技術參數
參數描述
PTH03050WADT 制造商:ARTESYN 制造商全稱:Artesyn Technologies 功能描述:DC-DC CONVERTERS POLA Non-isolated
PTH03050WAH 功能描述:DC/DC轉換器 6A 3.3V-In Wide Adj Module w/ Auto-Track RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓(標稱): 輸出端數量:1 輸出電壓(通道 1):3.3 V 輸出電流(通道 1):600 mA 輸出電壓(通道 2): 輸出電流(通道 2): 安裝風格:SMD/SMT 封裝 / 箱體尺寸:
PTH03050WAH 制造商:POWER TRENDS 功能描述:IC DC/DC 3.3VIN 6A ADJ O/P 3050 制造商:Texas Instruments 功能描述:IC DC/DC 3.3VIN 6A ADJ O/P 3050
PTH03050WAHT 制造商:ARTESYN 制造商全稱:Artesyn Technologies 功能描述:DC-DC CONVERTERS POLA Non-isolated
PTH03050WAS 功能描述:DC/DC轉換器 6A 3.3V-In Wide Adj Module w/ Auto-Track RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓(標稱): 輸出端數量:1 輸出電壓(通道 1):3.3 V 輸出電流(通道 1):600 mA 輸出電壓(通道 2): 輸出電流(通道 2): 安裝風格:SMD/SMT 封裝 / 箱體尺寸: