- 您現在的位置：買賣IC網 > PDF目錄378083 > PT7761-5V (Texas Instruments, Inc.) 40-A Programmable Integrated Switching Regulator Module PDF資料下載
參數資料
| 型號： | PT7761-5V |
| 廠商： | Texas Instruments, Inc. |
| 英文描述： | 40-A Programmable Integrated Switching Regulator Module |
| 中文描述： | 40集成的可編程開關穩壓器模塊 |
| 文件頁數： | 6/8頁 |
| 文件大?。?/td> | 176K |
| 代理商： | PT7761-5V |
For technical support and more information, see inside back cover or visit www.ti.com
Application Notes
continued
PT7761
Using the Standby Function on the PT7761
Excalibur
Integrated Switching Regulator
For applications requiring output voltage On/Off control,
the PT7761 integrated switching regulator (ISR) module
incorporates a standby function. This feature may be used
for power-up/shutdown sequencing, and to change the
output voltage while input power is applied.
See related
application notes:
“Pin-Coded Output Voltage Adjustment
of PT7761 Excalibur ISRs.”
The standby function is provided by the
STBY*
control,
pin 6. If pin 6 is left open-circuit the regulator operates
normally, providing a regulated output whenever a valid
supply voltage is applied to V
in
(pins 9–14) with respect to
GND (pins 16–22). Connecting pin 6 to ground
1
will set
the regulator output to zero volts
2
. This places the regu-
lator in standby mode, and reduces the input current to
typcially 30mA (60mA max). If a ground signal is applied
to pin 6 prior to power-up, the regulator output will be
held at zero volts during the period that input power is
applied.
The standby input must be controlled with an open-
collector (or open-drain) discrete transistor (See Figure 1).
Table 1 gives the threshold requirements.
Table 1 Standby Control Input Requirements
(1)
Parameter
Min
Enable
2V
Disable
–0.2V
I
stby
Vstby (o/c)
Typ
Max
Open Cct.
1
0.8V
0.4mA
V
in
Notes:
1. The Standby input on the PT7761 regulator must be
controlled using an open-collector (or open-drain) discrete
transistor.
Do Not
use a pull-up resistor. The control input
has an open-circuit voltage equal to V
in
. To set the
regulator output to zero, the control pin must be “pulled”
to less than 0.8Vdc with a 0.5mA sink to ground.
2. When placed in the standby mode, the regulator output
discharges the output capacitance with a low impedance to
ground.
3. The turn-off time of Q
1
, or rise time of the standby input
is not critical for the PT7761. Turning Q
1
off slowly, over
periods up to 100ms, will not affect regulator operation.
However, a slow turn-off time will increase both the initial
delay and rise-time of the output voltage.
Figure 1
Turn-On Time:
Turning Q
1
in Figure 1 off, removes the low-
voltage signal at pin 6 and enables the output. Following a
brief delay of approximately 10ms
3
, the output voltage of
the PT7761 series regulators rise to full regulation within
15ms
3
. Figure 2 shows the typical output voltage wave-
form of the PT7761 following the prompt turn-off of Q
1
at
time t =0 secs. The output voltage in Figure 1 is set to 3.3V
by connecting VID0 (pin 1), VID2 (pin 3), and VID3 (pin 4)
to the Rem Sense GND (pin 15)
*
. The waveform in Figure 2
was measured with a +5V input source voltage, and 10A resis-
tive load.
Figure 2
C
out
+
C
in
+
+5V
COM
Inhibit
L
O
A
D
+3.3V
COM
Q1
BSS138
PT7761
4
3
2
1
31
23
–
30
15
6
16
–
22
9
–
14
5
7
Sync
GND
Sns (+)
Sns (
–
)
V
OUT
V
IN
Stby
VID0 - VID4
*Consult the data sheet for details on other VID codes.
Vo (1V/Div)
Iin (5A/Div)
Vstby (5V/Div)
HORIZ SCALE: 5ms/Div
相關PDF資料 |
PDF描述 |
|---|---|
| PT7770 | 32A Programmable ISR Family |
| PT7777A | Synchronous Rectifier Driver, 2MHz Max Frequency, 500ns leadtime, Schmitt Trigger Input in a 20 Lead SSOP package |
| PT7777C | Dual Low Side Driver in a 8-lead SOIC package |
| PT78HT200 | 2A Wide Input Positive Step-Down ISR Family |
| PT78NR110S | 1 Amp Plus to Minus Voltage Integrated Switching Regulator(1A正到負電壓集成開關穩壓器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PT7761A | 功能描述:DC/DC轉換器 1.3V to 3.5V 40-A 5V Input Prog ISR RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
| PT7761C | 功能描述:REG 1.3-3.5V 40A 5VIN PROG SMD RoHS:否 類別:電源 - 板載 >> DC DC Converters 系列:PT7760 設計資源:Maxi/Mini/Micro Design Guide, Appl Manual 標準包裝:1 系列:Maxi 類型:隔離 輸出數:1 電壓 - 輸入（最小）:43V 電壓 - 輸入（最大）:110V Voltage - Output 1:15V Voltage - Output 2:- Voltage - Output 3:- 電流 - 輸出（最大）:* 電源（瓦） - 制造商系列:400W 電壓 - 隔離:* 特點:* 安裝類型:通孔 封裝/外殼:模塊 尺寸/尺寸:4.60" L x 2.20" W x 0.54" H（116.8mm x 55.9mm x 13.7mm） 包裝:散裝 工作溫度:-55°C ~ 100°C 效率:* 電源（瓦特）- 最大:* |
| PT7761N | 功能描述:DC/DC轉換器 1.3V to 3.5V 40-A 5V Input Prog ISR RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
| PT7769 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:40A ＇Current Booster＇ for the PT7761 ISR |
| PT7769N | 功能描述:DC/DC轉換器 40A Current Booster for the PT7761 ISR RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
發布緊急采購，3分鐘左右您將得到回復。