- 您現在的位置：買賣IC網 > PDF目錄368348 > PT7756N Intelligent Power Switch 1 Channel High Side Driver in a SO-8 Package PDF資料下載
參數資料
| 型號： | PT7756N |
| 英文描述： | Intelligent Power Switch 1 Channel High Side Driver in a SO-8 Package |
| 中文描述： | 模擬IC |
| 文件頁數： | 4/6頁 |
| 文件大?。?/td> | 128K |
| 代理商： | PT7756N |
For technical support and more information, see inside back cover or visit www.ti.com/powertrends
Application Notes
continued
Using the Standby Function on the PT7750
“Big Hammer III” Programmable ISRs
For applications requiring output voltage On/Off control,
the PT7750 “Big Hammer” ISRs incorporate a standby
function
1
. This feature may be used for power-up/shut-
down sequencing, and to change the output voltage while
input power is applied.
See related notes:
“Pin-coded Out-
put Voltage Adjustment on the ‘Big Hammer III’ Series
ISRs.”
The standby function is provided by the
STBY*
control,
pin 5. If pin 5 is left open-circuit the regulator operates
normally, providing a regulated output whenever a valid
supply voltage is applied to V
(pins 7-11) with respect to
GND (pins 13-19). Connecting pin 5 to ground
2
will set
the regulator output to zero volts
3
. This places the regu-
lator in standby mode, and reduces the input current to
typically 30mA (50mA max). If a ground signal is applied
to pin 5 prior to power-up, the regulator output will be
held at zero volts during the period that input power is
applied.
The standby input must be controlled with an open-col-
lector (or open-drain) discrete transistor (See Figure 1).
Table 1 gives the threshold requirements.
Table 1 Inhibit Control Threshold
2
Parameter
Min
Max
Disable (VIL)
–0.1V
0.3V
Notes:
1. The Standby/Inhibit control logic is similar for all Power
Trends’ modules, but the flexibility and threshold
tolerances will be different. For specific information on
this function for other regulator models, consult the
applicable application note.
2. The Standby input on the PT7750 regulator series must be
controlled using an open-collector (or open-drain) discrete
transistor.
Do Not
use a pull-up resistor. The control input
has an open-circuit voltage of about 1.5Vdc. To set the
regulator output to zero, the control pin must be “pulled”
to less than 0.3Vdc with a low-level 0.1mA sink to ground.
3. When placed in the standby mode, the regulator output
discharges the output capacitance with a low impedance to
ground. If an external voltage is applied to the output, it
will sink current and possibly over-stress the part.
4. The turn-off time of Q
, or rise time of the standby input
is not critical on the PT7750 series. Turning Q
off slowly,
over periods up to 100ms, will not affect regulator
operation. However, a slow turn-off time will increase
both the initial delay and rise-time of the output voltage.
Figure 1
Turn-On Time:
Turning Q
in Figure 1 off, removes the low-
voltage signal at pin 5 and enables the output. Following a
brief delay of 8-18ms, the output voltage of the PT7750 series
regulators rise to full regulation within 20ms
4
. Figure 2 shows
the typical output voltage waveform of a PT7751 following the
prompt turn-off of Q
at time t =0 secs. The output voltage in
Figure 1 is set to 5.0V by connecting VID0 (pin 1), VID3 (pin
4), and VID4 (pin 6) to the Remote Sense Gnd (pin 12)
*
. The
waveform in Figure 2 was measured with a 24V input source
voltage, and 10A resistive load.
Figure 2
C
out
+
C
in
+
+24V
COM
Inhibit
L
O
A
D
V
o
=5.0V
COM
Q1
BSS138
PT7750
6
4
3
2
1
26
20-25
12
5
13-19
27
7-11
Vo
Vin
GND
SNS(+)
SNS(-)
Synch
Out
STBY
VID4 - VID0
*
Consult the data sheet for details on other VID codes.
PT7750 Series
0
5
10
15
20
25
t (milli - secs)
V
in
(2V/Div)
相關PDF資料 |
PDF描述 |
|---|---|
| PT7761 | Intelligent Power Switch 1 Channel High Side Driver in a SO-8 Package |
| PT7761A | Intelligent Power Switch 1 Channel High Side Driver in a TO-220FL Package |
| PT7761C | Intelligent Power Switch 1 Channel High Side Driver in a D2-Pak 5-Lead Package |
| PT7761N | Intelligent Power Switch 1 Channel High Side Driver in a D2-Pak 5-Lead Package |
| PT7769 | Intelligent Power Switch 1 Channel High Side Driver in a TO-220FL Package |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PT7761 | 制造商:DATATRONIC 功能描述: |
| PT7761-5V | 制造商:TI 制造商全稱:Texas Instruments 功能描述:40-A Programmable Integrated Switching Regulator Module |
| PT7761A | 功能描述:DC/DC轉換器 1.3V to 3.5V 40-A 5V Input Prog ISR RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
| PT7761C | 功能描述:REG 1.3-3.5V 40A 5VIN PROG SMD RoHS:否 類別:電源 - 板載 >> DC DC Converters 系列:PT7760 設計資源:Maxi/Mini/Micro Design Guide, Appl Manual 標準包裝:1 系列:Maxi 類型:隔離 輸出數:1 電壓 - 輸入（最?。?43V 電壓 - 輸入（最大）:110V Voltage - Output 1:15V Voltage - Output 2:- Voltage - Output 3:- 電流 - 輸出（最大）:* 電源（瓦） - 制造商系列:400W 電壓 - 隔離:* 特點:* 安裝類型:通孔 封裝/外殼:模塊 尺寸/尺寸:4.60" L x 2.20" W x 0.54" H（116.8mm x 55.9mm x 13.7mm） 包裝:散裝 工作溫度:-55°C ~ 100°C 效率:* 電源（瓦特）- 最大:* |
| PT7761N | 功能描述:DC/DC轉換器 1.3V to 3.5V 40-A 5V Input Prog ISR RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
發布緊急采購，3分鐘左右您將得到回復。