- 您現在的位置：買賣IC網 > PDF目錄378083 > PT7743N (Texas Instruments, Inc.) RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS PDF資料下載
參數資料
| 型號： | PT7743N |
| 廠商： | Texas Instruments, Inc. |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS |
| 中文描述： | 抗輻射高效，5安培開關穩壓器 |
| 文件頁數： | 6/7頁 |
| 文件大?。?/td> | 172K |
| 代理商： | PT7743N |
Application Notes
For technical support and more information, see inside back cover or visit www.ti.com
Pin-Coded Output Voltage Adjustment of
20-A Programmable Regulators
The 20-A family of programmable ISRs incorporate a pin-
coded control to adjust the output voltage. This feature
uses the control pins VID0–VID4 (pins 1–6). When
the control pins are left open-circuit, the ISR output
regulates at its default output voltage. Each control pin
is internally connected to a precision resistor, which
when grounded applies a weighted change to the output
voltage. By selectively grounding VID0–VID4, the output
voltage of these ISRs can be programmed in incremental
steps over the module’s output voltage range. The program
codes and output voltage range offered by these ISRs are
compatible with the Voltage ID specifications defined by
Intel Corporation for VRMs (voltage regulator mod-
ules). The codes are used by both the Pentium and
Athlon microprocessors. Refer to Figure 1 for the
connection schematic, and the respective device Data Sheet
for the programming code information.
Notes:
1. The programming convention is as follows:
Logic 0:
Connect to pin 12 (Remote Sense Ground).
Logic 1:
Open circuit/open drain (See notes 2, & 4)
2. Do not connect pull-up resistors to the voltage
programming pins.
3. Use pin 12 (Remote Sense Ground) as the logic “0”
reference. While the regular ground (pins 13-19) can also
be used for programming, doing so will degrade the load
reglation of the product. If the remote sense ground is
not used, pin 12 must be connected to pin 13 for
optimum output voltage accuracy.
Figure 1
4. If active devices are used to ground the voltage control
pins, low-level open drain MOSFET devices should be
used over bipolar transistors. The inherent V
ce
(sat) in
bipolar devices introduces errors in the device’s internal
divider network. Discrete transistors such as the BSS138,
2N7002, or IRLML2402 are examples of appropriate
devices.
Active Voltage Programming:
Special precautions should be taken when making changes
to the voltage control progam code while the unit is
powered. It is highly recommended that the ISR be either
powered down or held in standby. Changes made to the
program code while V
out
is enabled induces high current
transients through the device. This is the result of the
electrolytic output capacitors being either charged or
discharged to the new output voltage set-point. The
transient current can be minimized by making only in-
cremental changes to the binary code, i.e. one LSB at a
time. A minimum of 100μs settling time between each
program state is also recommended. Making non-
incremental changes to VID3 or VID4 while the output
is enabled is discouraged. The transients induced can
overstress the device. If the program code cannot be
asserted priot to power-up, pull pin 5 (STBY) control to
GND during the period that the input voltage is applied
to V
in
. Releasing pin 5 will then allow the device to per-
form a soft-start to the programmed voltage. For more
information on the use of the Standby function, consult
the related application note, “Using the Standby Function
on 20-A Programmable Switching Regulators”
C
out
+
C
in
+
1μH
(Optional)
+5V
COM
STBY
L
O
A
D
6
4
3
2
1
26
20-25
12
5
13-19
27
7-11
Vo
Vin
GND
SNS(+)
SNS(-)
Synch
Out
STBY
VID4 - VID0
PT770X/PT761X
PT7708/09, PT7615
相關PDF資料 |
PDF描述 |
|---|---|
| PT7615A | RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS |
| PT7761-5V | 40-A Programmable Integrated Switching Regulator Module |
| PT7770 | 32A Programmable ISR Family |
| PT7777A | Synchronous Rectifier Driver, 2MHz Max Frequency, 500ns leadtime, Schmitt Trigger Input in a 20 Lead SSOP package |
| PT7777C | Dual Low Side Driver in a 8-lead SOIC package |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PT7744 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:20 Amp ＇Current Booster＇ for PT7712 ISR |
| PT7744A | 功能描述:REGULATR 20A BSTR FOR PT7712 HRZ RoHS:否 類別:電源 - 板載 >> DC DC Converters 系列:PT7740 標準包裝:10 系列:PT4570 類型:隔離 輸出數:1 電壓 - 輸入（最小）:36V 電壓 - 輸入（最大）:75V Voltage - Output 1:9V Voltage - Output 2:- Voltage - Output 3:- 電流 - 輸出（最大）:3.3A 電源（瓦） - 制造商系列:30W 電壓 - 隔離:1.5kV（1500V） 特點:- 安裝類型:表面貼裝 封裝/外殼:19-SIP SMD 模塊 尺寸/尺寸:3.00" L x 1.19" W x 0.50" H（76.2mm x 30.2mm x 12.7mm） 包裝:托盤 工作溫度:-40°C ~ 85°C 效率:84% 電源（瓦特）- 最大:30W |
| PT7744C | 功能描述:REGULATR 20A BSTR FOR PT7712 SMD RoHS:否 類別:電源 - 板載 >> DC DC Converters 系列:PT7740 標準包裝:10 系列:PT4570 類型:隔離 輸出數:1 電壓 - 輸入（最小）:36V 電壓 - 輸入（最大）:75V Voltage - Output 1:9V Voltage - Output 2:- Voltage - Output 3:- 電流 - 輸出（最大）:3.3A 電源（瓦） - 制造商系列:30W 電壓 - 隔離:1.5kV（1500V） 特點:- 安裝類型:表面貼裝 封裝/外殼:19-SIP SMD 模塊 尺寸/尺寸:3.00" L x 1.19" W x 0.50" H（76.2mm x 30.2mm x 12.7mm） 包裝:托盤 工作溫度:-40°C ~ 85°C 效率:84% 電源（瓦特）- 最大:30W |
| PT7744N | 功能描述:開關變換器、穩壓器與控制器 20A Current Booster for PT7712 ISR RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel |
| PT7745 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:20 Amp ＇Current Booster＇ for PT7711 ISR |
發布緊急采購，3分鐘左右您將得到回復。