- 您現在的位置：買賣IC網 > PDF目錄370025 > PT7712 600V Half Bridge Driver LED Buck Regulator in a 8-Pin SOIC Package; A IRS2541 packaged in a Lead-Free 8-Lead SOIC shipped on Tape and Reel PDF資料下載
參數資料
| 型號： | PT7712 |
| 英文描述： | 600V Half Bridge Driver LED Buck Regulator in a 8-Pin SOIC Package; A IRS2541 packaged in a Lead-Free 8-Lead SOIC shipped on Tape and Reel |
| 中文描述： | 20安培3.3V的輸入下一代\u0026#39;大鐵錘\u0026#39;可編程ISR的 |
| 文件頁數： | 7/8頁 |
| 文件大?。?/td> | 157K |
| 代理商： | PT7712 |
For technical support and more information, see inside back cover or visit www.ti.com
Application Notes
PT7710 Family
Pin-Coded Output Voltage Adjustment of the
PT7710 Excalibur
Series of 20-A ISRs
The PT7710 Excalibur family of converters incorporate
a pin-coded control to adjust the output voltage. This
feature uses the control pins VID0–VID4 (pins 1–6).
When the control pins are left open-circuit, the ISR
output regulates at its default output voltage. Each
control pin is internally connected to a precision resistor,
which when grounded applies a weighted change to the
output voltage. By selectively grounding VID0–VID4,
the output voltage of these ISRs can be programmed in
incremental steps over the specified output voltage range.
The program codes and output voltage range offered by
these ISRs are compatible with the Voltage ID specifica-
tions defined by Intel Corporation for VRMs (voltage
regulator modules). The codes are used by both the
Pentium and Athlon microprocessors. Refer to
Figure 4-1 for the connection schematic, and the respective
device Data Sheet for the programming code information.
Notes:
1. The programming convention is as follows:-
Logic 0:
Connect to pin 12 (Remote Sense Ground).
Logic 1:
Open circuit/open drain (See notes 2, & 4)
2. Do not connect pull-up resistors to the voltage
programming pins.
3. Use pin 12 (Remote Sense Ground) as the logic “0”
reference. While the regular ground (pins 13-19) can also
be used for programming, doing so will degrade the load
reglation of the product. If the remote sense ground is
not used, pin 12 must be connected to pin 13 for
optimum output voltage accuracy.
Figure 4-1
4. If active devices are used to ground the voltage control
pins, low-level open drain MOSFET devices should be
used over bipolar transistors. The inherent V
ce
(sat) in
bipolar devices introduces errors in the device’s internal
divider network. Discrete transistors such as the BSS138,
2N7002, or IRLML2402 are examples of appropriate
devices.
Active Voltage Programming:
Special precautions should be taken when making changes
to the output voltage progam code while the unit is
powered. This activity can induce current transients
through the device as a result of the electrolytic output
capacitors being either charged or discharged to the new
output voltage set-point. The transient current can be
minimized by making only incremental changes to the
binary code, i.e. one LSB at a time. A minimum of 100μs
settling time between each program state is also recom-
mended. Making non-incremental changes to VID3 or
VID4 is discouraged.
When active devices are used to program the output
voltage, their state should be asserted prior to the input
power being applied. An alternative is to pull pin 5 (STBY)
control to GND during the application of input voltage,
then assert the required program code and release pin 5.
The module will then intiate a soft-start power-up to the
desired program voltage. For more information on the
use of the Standby function, consult the related applica-
tion note, “Using the Standby Function on the PT7710
Excalibur Series of 20-A ISRs.”
C
out
+
C
in
+
1μH
(Optional)
+5V
COM
STBY
L
O
A
D
PT7710
6
4
3
2
1
26
20-25
12
5
13-19
27
7-11
Vo
Vin
GND
SNS(+)
SNS(-)
Synch
Out
STBY
VID4 - VID0
相關PDF資料 |
PDF描述 |
|---|---|
| PT7713 | 200V Half Bridge Driver LED Buck Regulator in a 8-Lead Dip Package; A IRS2540 packaged in a Lead-Free 8-Lead DIP |
| PT7714 | 200V Half Bridge Driver LED Buck Regulator in a 8-Pin SOIC Package; A IRS2540 packaged in a Lead-Free 8-Lead SOIC shipped on Tape and Reel |
| PT7715 | Single High Side Driver, Noninverting Input. IN Voltage Threshold 9.5V & 6.0V; A IRS2118 packaged in a Lead-Free 8-Lead SOIC |
| PT7716 | 20-A 1.075V to 1.85V 3.3V-Input Programmable ISR |
| PT7721A | SMPS Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PT7712A | 功能描述:開關變換器、穩壓器與控制器 20A 3.3Vin Next Gen Programmable ISR RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel |
| PT7712C | 功能描述:REGULATR 1.3-3.5V 20A 3.3VIN SMD RoHS:是 類別:電源 - 板載 >> DC DC Converters 系列:PT7710 標準包裝:10 系列:PT4570 類型:隔離 輸出數:1 電壓 - 輸入（最小）:36V 電壓 - 輸入（最大）:75V Voltage - Output 1:9V Voltage - Output 2:- Voltage - Output 3:- 電流 - 輸出（最大）:3.3A 電源（瓦） - 制造商系列:30W 電壓 - 隔離:1.5kV（1500V） 特點:- 安裝類型:表面貼裝 封裝/外殼:19-SIP SMD 模塊 尺寸/尺寸:3.00" L x 1.19" W x 0.50" H（76.2mm x 30.2mm x 12.7mm） 包裝:托盤 工作溫度:-40°C ~ 85°C 效率:84% 電源（瓦特）- 最大:30W |
| PT7712N | 功能描述:開關變換器、穩壓器與控制器 20A 3.3Vin Next Gen Programmable ISR RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel |
| PT7712VD | 制造商:TI 制造商全稱:Texas Instruments 功能描述:20-A Programmable Integrated Switching Regulator |
| PT7713 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:20-A 1.8V to 2.55V 3.3V-Input Programmable ISR |
發布緊急采購，3分鐘左右您將得到回復。