參數資料
型號: PT5804A
廠商: TEXAS INSTRUMENTS INC
元件分類: 穩壓器
英文描述: 18 A SWITCHING REGULATOR, 350 kHz SWITCHING FREQ-MAX, SMA18
封裝: SIP-18
文件頁數: 2/13頁
文件大?。?/td> 228K
代理商: PT5804A
Application Notes
For technical support and more information, see inside back cover or visit www.ti.com
Using the Margin Up/Down Controls on the
PT5800 & PT5810 Regulator Series
The PT5800 & PT5810 series of integrated switching
regulator modules incorporate Margin Up* (pin 4) and
Margin Dn* (pin 3) control inputs. These controls allow the
output voltage set point to be momentarily adjusted 1,
either up or down, by a nominal 5%. This provides a
convenient method for dynamically testing the load
circuit’s power supply voltage over its operating margin
or range. Note that the ±5% change is also applied to any
adjustment of the output voltage, if made, using the Vo
Adjust (pin 1).
The 5% adjustment is made by driving the appropriate
margin control input directly to the ground reference at
Sense(-) (pin 8) 2. An low-leakage open-drain device, such as
a MOSFET or a p-channel JFET is recommended for this
purpose. Adjustments of less than 5% can also be accom-
modated by adding series resistors to the control inputs
(See Figure 6-1). The value of the resistor can be selected
from Table 6-1, or calculated using the following formula.
Resistor Value Calculation
To reduce the margin adjustment to something less than
5%, series padding resistors are required (See RD and
RU in Figure 6-1). For the same amount of adjustment,
the resistor value calculated for RU and RD will be the
same. The formulas is as follows.
RU/RD =
499
– 99.8
k
%
Where
% = The desired amount of margin adjust in
percent.
Notes:
1. The Margin Up* and Margin Dn* controls were not
intended to be activated simultaneously. If they are
their affects on the output voltage may not completely
cancel, resulting in a slight shift in the output voltage
set point.
2. When possible use the Sense(-) (pin 8) as the ground
reference. This will produce a more accurate adjustment
of the output voltage at the load circuit terminals. GND
(pins 9-13) can be used if the Sense(-) pin is connected
to GND near the regulator.
C
out
+
C
in
+5V
GND
MargDn
L
O
A
D
Q
2
Sense(–)
+V
OUT
GND
PT5800
18
14–17
8
29–13
5, 6, 7
V
OUT
V
IN
GND
SNS(+)
SNS(–)
INHIBIT*
Q
1
4
3
MARG
DN*
MARG
UP*
+
MargUp
0V
+V
o
R
D
R
U
0V
Figure 6-1; Margin Up/Down Application Schematic
Table 6-1; Margin Up/Down Resistor Values
PADDING RESISTOR VALUES
% Adjust
RU / RD
5
0.0k
4
24.9k
3
66.5k
2
150.0k
1
397.0k
PT5800 & PT5810 Series
相關PDF資料
PDF描述
PT5806C 18 A SWITCHING REGULATOR, 350 kHz SWITCHING FREQ-MAX, SMA18
PT5802C 18 A SWITCHING REGULATOR, 350 kHz SWITCHING FREQ-MAX, SMA18
PT5801N 18 A SWITCHING REGULATOR, 350 kHz SWITCHING FREQ-MAX, SMA18
PT5801A 18 A SWITCHING REGULATOR, 350 kHz SWITCHING FREQ-MAX, SMA18
PT5822A 16 A SWITCHING REGULATOR, 400 kHz SWITCHING FREQ-MAX, MSMA18
相關代理商/技術參數
參數描述
PT5804C 功能描述:DC/DC轉換器 1.5V 18-A 5-V Input Adj Step-Down ISR RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓(標稱): 輸出端數量:1 輸出電壓(通道 1):3.3 V 輸出電流(通道 1):600 mA 輸出電壓(通道 2): 輸出電流(通道 2): 安裝風格:SMD/SMT 封裝 / 箱體尺寸:
PT5804N 功能描述:DC/DC轉換器 1.5V 18-A 5-V Input Adj Step-Down ISR RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓(標稱): 輸出端數量:1 輸出電壓(通道 1):3.3 V 輸出電流(通道 1):600 mA 輸出電壓(通道 2): 輸出電流(通道 2): 安裝風格:SMD/SMT 封裝 / 箱體尺寸:
PT5805 制造商:未知廠家 制造商全稱:未知廠家 功能描述:18-A 5-V Input Adjustable Integrated Switching Regulator
PT580524 功能描述:通用繼電器 4PDT 24VAC SHRACK RoHS:否 制造商:Omron Electronics 觸點形式:1 Form A (SPST-NO) 觸點電流額定值:150 A 線圈電壓:24 VDC 線圈電阻:144 Ohms 線圈電流:167 mA 切換電壓:400 V 安裝風格:Chassis 觸點材料:
PT5805A 功能描述:開關變換器、穩壓器與控制器 1.2V 18-A 5-V Input Adj Step-Down ISR RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel