- 您現在的位置：買賣IC網 > PDF目錄69171 > PT4856N (TEXAS INSTRUMENTS INC) 3-OUTPUT DC-DC REG PWR SUPPLY MODULE PDF資料下載
參數資料
| 型號： | PT4856N |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 電源模塊 |
| 英文描述： | 3-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| 封裝： | SIP-26/25 |
| 文件頁數： | 2/15頁 |
| 文件大?。?/td> | 268K |
| 代理商： | PT4856N |
第1頁當前第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁
For technical support and more information, see inside back cover or visit www.ti.com
Application Notes
PT4850 Series
Figure 3; Vo1, Vo2, Vo3 Power-Up Sequence
On/Off Output Voltage Sequencing
The power-up characteristic of the PT4850 series of
DC/DC converters meets the requirements of micro-
processor and DSP chipsets. All three outputs from the
converter are internally sequenced to power up in
unison. Figure 3 shows the waveforms from a PT4851
after power is applied to the input of the converter.
During power-up, all three output voltages rise together
until each reaches their respective output voltage. The
waveforms of Figure 3 were measured with loads of ap-
proximately 50% on each output, with an input source of
48VDC. The converter typically produces a fully regu-
lated output within 150ms.
Using the On/Off Enable Controls on the PT4850
Series of Triple Output DC/DC Converters
The PT4850 (48V input) series of 25-A, triple-output
DC/DC converters incorporate two output enable controls.
EN1 (pin 3) is the Negative Enable input, and EN2 (pin 4)
is the Positive Enable input. Both inputs are electrically
referenced to -Vin (pin 2) on the primary or input side of
the converter. A pull-up resistor is not required, but may
be added if desired. Voltages of up to 70V can be safely
applied to the either of the Enable pins.
Automatic (UVLO) Power-Up
Connecting EN1 (pin 3) to -Vin (pin 2) and leaving EN2
(pin 4) open-circuit configures the converter for auto-
matic power up. (See data sheet “Typical Application”).
The converter control circuitry incorporates an “Under
Voltage Lockout” (UVLO) function, which disables the
converter until the minimum specified input voltage is
present at ±Vin. (See data sheet Specifications). The UVLO
circuitry ensures a clean transition during power-up and
power-down, allowing the converter to tolerate a slow-
rising input voltage. For most applications EN1 and
EN2, can be configured for automatic power-up.
Positive Output Enable (Negative Inhibit)
To configure the converter for a positive enable func-
tion, connect EN1 (pin 3) to -Vin (pin 2), and apply the
system On/Off control signal to EN2 (pin 4). In this
configuration, a low-level input voltage (-Vin potential)
applied to pin 4 disables the converter outputs. Figure 1
is an example of this configuration.
Negative Output Enable (Positive Inhibit)
To configure the converter for a negative enable function,
EN2 (pin 4) is left open circuit, and the system On/Off
control signal is applied to EN1 (pin 3). A low-level
input voltage (-Vin potential) must then be applied to
DC/DC
Module
EN 1*
EN 2
–Vin
–V
IN
1 =Outputs Off
4
3
2
BSS138
DC/DC
Module
EN 1*
EN 2
–Vin
–V
IN
1 =Outputs On
4
3
2
BSS138
Figure 2; Negative Enable Configuration
Figure 1; Positive Enable Configuration
During turn-off, all outputs drop rapidly due to the
discharging effect of actively switched rectifiers. The
voltage at Vo2 remains higher than Vo3 during this
period. The discharge time is typically 100s, but will
vary with the amount of external load capacitance.
pin 3 in order to enable the outputs of the converter.
An example of this configuration is detailed in Figure 2.
Note: The converter will only produce and output voltage if a
valid input voltage is applied to ±Vin.
Vo1 (1V/Div)
V02 (1V/Div)
Vo3 (1V/Div)
HORIZ SCALE: 20ms/Div
相關PDF資料 |
PDF描述 |
|---|---|
| PT4854N | 3-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| PT4855C | 3-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| PT4854C | 3-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| PT4853C | 3-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| PT4856C | 3-OUTPUT DC-DC REG PWR SUPPLY MODULE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PT491 | 制造商:SHARP 制造商全稱:Sharp Electrionic Components 功能描述:Intermediate Acceptance High Sensitivity Phototransistor |
| PT491F | 制造商:SHARP 制造商全稱:Sharp Electrionic Components 功能描述:Intermediate Acceptance High Sensitivity Phototransistor |
| PT491FE0000F | 功能描述:光電晶體管 860nm 0.8mA RoHS:否 制造商:OSRAM Opto Semiconductors 最大功率耗散:165 mW 最大暗電流:200 nA 封裝 / 箱體:T-1 |
| PT-49266-R | 制造商:JAMECO VALUEPRO 功能描述:POWER TRANSFORMER,24.6VCT@2A,117VAC,WIRE LEADS |
| PT493 | 制造商:SHARP 制造商全稱:Sharp Electrionic Components 功能描述:Intermediate Acceptance High Sensitivity Phototransistor |
發布緊急采購，3分鐘左右您將得到回復。