參數資料
型號： PT4833C
廠商： TEXAS INSTRUMENTS INC
元件分類： 電源模塊
英文描述： 3-OUTPUT 35 W DC-DC REG PWR SUPPLY MODULE
封裝： METAL, SIP-21/18
文件頁數： 21/34頁
文件大小： 483K
代理商： PT4833C
For technical support and more information, see inside back cover or visit www.ti.com
Application Notes
28
PT4820 Series
On/Off Enable Turn-On Time
When the On/Off enable inputs, EN1 or EN2 are used
to enable the PT4820's output voltages, the turn-on
delay time (measured from the transition of the enable
signal to the instance the outputs begin to rise) will vary
with the input voltage and the module’s internal timing.
At an input voltage of 48V, the total turn-on time is
between 20 and 60 milliseconds. This turn-on time
reduces as the input voltage is increased. The rise time
of the output voltages is between 10 and 15 milliseconds.
Using the On/Off Enable Controls on the PT4820
Series of Triple Output DC/DC Converters
The PT4820 (48V input) series of triple-output DC/DC
converters incorporate two output enable controls. EN1
(pin 1) is the Positive Enable input, and EN2 (pin 2) is the
Negative Enable input. Both inputs are electrically refer-
enced to -Vin (pin 4) on the primary or input side of the
converter. The Enable pins are ideally controlled with an
open-collector (or open-drain) discrete transistor. A pull-
up resistor is not required. If a pull-up resistor is added,
the pull-up voltage must be limited to 15V.
Automatic (UVLO) Power-Up
Connecting EN2 (pin 2) to -Vin (pin 4) and leaving EN1
(pin 1) open-circuit configures the converter for auto-
matic power up. (See data sheet “Typical Application”).
The converter control circuitry incorporates an “Under
Voltage Lockout” (UVLO) function, which disables the
converter until the minimum specified input voltage is
present at ±Vin. (See data sheet Specifications). The UVLO
circuitry ensures a clean transition during power-up and
power-down, allowing the converter to tolerate a slow-
rising input voltage. For most applications EN1 and
EN2, can be configured for automatic power-up.
Positive Output Enable (Negative Inhibit)
To configure the converter for a positive enable func-
tion, connect EN2 (pin 2) to -Vin (pin 4), and apply the
system On/Off control signal to EN1 (pin 1). In this
configuration, applying less than 0.8V (with respect to
-Vin potential) to pin 1 disables the converter outputs.
Figure 2-1 is an example of this implemention using a
buffer transistor.
DC/DC
Module
EN 1
EN 2
–Vin
–V
IN
1 =Outputs Off
1
2
4
BSS138
DC/DC
Module
EN 1
EN 2
–Vin
–V
IN
1 =Outputs On
1
2
4
BSS138
Figure 2-2; Negative Enable Configuration
Figure 2-1; Positive Enable Configuration
Negative Output Enable (Positive Inhibit)
To configure the converter for a negative enable function,
EN1 (pin 1) is left open circuit, and the system On/Off
control signal is applied to EN2 (pin 2). Applying less
than 0.8V (with respect to -Vin potential) to pin 2, enables
the converter outputs. An example using a buffer transistor
is again detailed in Figure 2-2. Note: The converter will
only produce and output voltage if a valid input voltage is
applied to ±Vin.
相關PDF資料
PDF描述
PT4827N 3-OUTPUT 35 W DC-DC REG PWR SUPPLY MODULE
PT4824A 3-OUTPUT 35 W DC-DC REG PWR SUPPLY MODULE
PT4825A 3-OUTPUT 35 W DC-DC REG PWR SUPPLY MODULE
PT4826A 3-OUTPUT 35 W DC-DC REG PWR SUPPLY MODULE
PT4832A 3-OUTPUT 35 W DC-DC REG PWR SUPPLY MODULE
相關代理商/技術參數
參數描述
PT4833N 功能描述:直流/直流開關轉換器 3.3/2/1.5 V 12A 48V Inpt Iso DC/DC Cnvtr RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT
PT483F1 制造商:SHARP 制造商全稱:Sharp Electrionic Components 功能描述:Narrow Acceptance High Sensitivity Phototransistor
PT483F1E000F 功能描述:光電晶體管 Long Ver of PT481F RoHS:否 制造商:OSRAM Opto Semiconductors 最大功率耗散:165 mW 最大暗電流:200 nA 封裝 / 箱體:T-1
PT4840A 制造商:TI 制造商全稱:Texas Instruments 功能描述:65-W TRIPLE OUTPUT ISOLATED DC/DC CONVERTER FOR DSL APPLICATIONS
PT4841 制造商:未知廠家 制造商全稱:未知廠家 功能描述:15V/3.3V/1.5V 48V-Input 65 Watt Triple-Output DC/DC Converter
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*