- 您現在的位置：買賣IC網 > PDF目錄96791 > PT4485A (TEXAS INSTRUMENTS INC) 1-OUTPUT 100 W DC-DC REG PWR SUPPLY MODULE PDF資料下載
參數資料
| 型號： | PT4485A |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 電源模塊 |
| 英文描述： | 1-OUTPUT 100 W DC-DC REG PWR SUPPLY MODULE |
| 封裝： | SIP-26 |
| 文件頁數： | 6/9頁 |
| 文件大?。?/td> | 213K |
| 代理商： | PT4485A |
Application Notes
For technical support and further information, visit http://power.ti.com
Using the Inhibit Function on the PT4470 &
PT4480 Series of Isolated DC/DC Converters
The PT4470/44480 series of DC/DC converters incor-
porate an On/Off Inhibit function. This function may be
used in applications that demand battery conservation,
power-up/shutdown sequencing, and/or to coordinate
power-up for active in-rush current control.
The On/Off feature is provided by the Inhibit control,
pin 3. The Inhibit pin of the PT4470/4480 series of
converters is an active low enable. The pin must be
either connected, or actively pulled low, to –Vin (pin 2)
to enable the converter output (see standard applica-
tion schematic). When pins 2 & 3 are connected, the
converter provides a regulated output whenever a valid
source voltage3 is applied between +Vin (pin 1), and –Vin
(pin 2). If pin 3 is disconnected, or allowed to become
high impedance, the regulator output will be disabled. 5
Table 2-1 provides details of the interface requirements
for the Inhibit pin. Figure 2-1 shows how a discrete
MOSFET (Q1) 4, may be referenced to –Vin and used to
control the input.
Table 2-1 Inhibit Control Requirements
Parameter
Min
Max
Enable (VIH)
–0.5 V
0.8 V
Disable (VIL)
2.5 V
(Open Circuit)
Notes:
1. The Inhibit control uses –Vin (pin 2), on the primary side
of the converter, as its ground reference. All voltages
specified are with respect to –Vin.
2. The internal circuitry is simple pull-up resistor. The
open-circuit voltage may be as high as 6.5 Vdc.
3. These converters incorporate an “Under-Voltage
Lockout” (UVLO) function. This function automatically
disables the converter output until there is sufficient input
voltage to produce a regulated output. Table 2 gives the
applicable UVLO thresholds.
Table 2-2 UVLO Thresholds 1
Series
UVLO Threshold
Vin Range
PT4470
17 V Typical
18 – 36 V
PT4480
34.5 V Typical
36 – 75 V
4. The Inhibit input must be controlled with an open-
collector (or open-drain) discrete transistor or
MOSFET.
Do not use a pull-up resistor.
5. When the converter output is disabled, the current
drawn from the input supply is typically reduced to
4 mA (10 mA maximum).
Figure 2-1
Turn-On Time:
With input power applied, the converter
typically produces a fully regulated output voltage within
25 ms after applying a low-voltage signal to the Inhibit
control pin. The actual turn-on time will vary with
the input voltage, output load, and the total amount of
capacitance connected to the output. Using the circuit of
Figure 2-1, Figure 2-2 shows the typical output voltage
and input current waveforms of a PT4472 after Q1 is
turned on. The turn on of Q1 correlates to the fall in
Vinh. The output voltage was set to 2.5 V. The waveform
was measured with a 48-Vdc input voltage, and 15-A load
current.
Figure 2-2
PT4470, PT4480 Series
6. Keep the on/off transition to less than 1ms. This
prevents erratic operation of the ISR, whereby the
output voltage may drift un-regulated between 0 V
and the rated output during power-up.
Vout (1V/Div)
Iin (2A/Div)
Vinh (5V/Div)
HORIZ SCALE: 5ms/Div
PT4472
+V
sns
+V
out
-V
out
-V
sns
7
8-13
14-19
20
21
25
22
24
23
VID0 - VID4
+V
in
–V
in
1
2
3
Inhibit
C
1
+
PROGRAMMING PINS
+2.5V
+V
IN
–V
IN
0V
1 =Enable
Q
1
BSS138
相關PDF資料 |
PDF描述 |
|---|---|
| PT4485N | 1-OUTPUT 100 W DC-DC REG PWR SUPPLY MODULE |
| PT4486C | 1-OUTPUT 100 W DC-DC REG PWR SUPPLY MODULE |
| PT4493A | 1-OUTPUT 100 W DC-DC BOOSTER MODULE |
| PT4493N | 1-OUTPUT 100 W DC-DC BOOSTER MODULE |
| PT4476N | 1-OUTPUT 100 W DC-DC REG PWR SUPPLY MODULE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PT4485C | 功能描述:CONV DC 12VADJ 48VIN 8.5A HZ SMD RoHS:是 類別:電源 - 板載 >> DC DC Converters 系列:PT4480 標準包裝:10 系列:PT4570 類型:隔離 輸出數:1 電壓 - 輸入（最?。?36V 電壓 - 輸入（最大）:75V Voltage - Output 1:9V Voltage - Output 2:- Voltage - Output 3:- 電流 - 輸出（最大）:3.3A 電源（瓦） - 制造商系列:30W 電壓 - 隔離:1.5kV（1500V） 特點:- 安裝類型:表面貼裝 封裝/外殼:19-SIP SMD 模塊 尺寸/尺寸:3.00" L x 1.19" W x 0.50" H（76.2mm x 30.2mm x 12.7mm） 包裝:托盤 工作溫度:-40°C ~ 85°C 效率:84% 電源（瓦特）- 最大:30W |
| PT4485N | 功能描述:直流/直流開關轉換器 100W 48V-Input 12V Output Iso DC/DC RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| PT4486 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:100-W 30-A Programmable Isolated DC/DC Converter |
| PT4486A | 功能描述:CONV DC-DC 12VADJ 48VIN 8.5A HRZ RoHS:是 類別:電源 - 板載 >> DC DC Converters 系列:PT4480 標準包裝:10 系列:PT4570 類型:隔離 輸出數:1 電壓 - 輸入（最?。?36V 電壓 - 輸入（最大）:75V Voltage - Output 1:9V Voltage - Output 2:- Voltage - Output 3:- 電流 - 輸出（最大）:3.3A 電源（瓦） - 制造商系列:30W 電壓 - 隔離:1.5kV（1500V） 特點:- 安裝類型:表面貼裝 封裝/外殼:19-SIP SMD 模塊 尺寸/尺寸:3.00" L x 1.19" W x 0.50" H（76.2mm x 30.2mm x 12.7mm） 包裝:托盤 工作溫度:-40°C ~ 85°C 效率:84% 電源（瓦特）- 最大:30W |
| PT4486C | 功能描述:開關變換器、穩壓器與控制器 100W 48V-Input 12V Out Iso DC/DC Conv RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。