- 您現在的位置：買賣IC網 > PDF目錄368336 > PT4214 12Vout 7W 48V-Input Isolated DC/DC Converter PDF資料下載
參數資料
| 型號： | PT4214 |
| 英文描述： | 12Vout 7W 48V-Input Isolated DC/DC Converter |
| 中文描述： | 12Vout 7瓦48V的輸入隔離DC / DC轉換器 |
| 文件頁數： | 3/5頁 |
| 文件大小： | 209K |
| 代理商： | PT4214 |
Application Notes
For technical support and more information, see inside back cover or visit www.ti.com/powertrends
PT4210 Series
Using the Remote On/Off Function on the
PT4210 Isolated 7W DC/DC Converters
Applications requiring output voltage On/Off control, the
PT4210 DC/DC converter series incorporates a
“Remote
On/Off”
control (pin 11). This feature can be used when
there is a requirement for the module to be switched off
without removing the applied input source voltage.
The converter functions normally with Pin 11 open-circuit,
providing a regulated output voltage when a valid source
voltage is applied to +V
in
(pin 18), with respect to –V
in
(pin 17). When a low-level
1
ground signal is applied to
pin 11, the converter output will be turned off.
Figure 1 shows an application schematic, which details
the typical use of the
Remote On/Off
function. Note the
discrete transistor (Q1). The control pin has its own
internal pull-up, and must be controlled with an open-
collector or open-drain device (See notes 2 & 3). Table 1
gives the input requirements.
When placed in the “Off” state, the standby current drawn
from the input source is typically reduced to less than 1mA.
Table 1; Remote On/Off Control Requirements
1
Parameter
Min
Typ
Max
Disable
Enable
Vo/c [Open-Circuit]
Iin [pin 11 at –Vin]
-0.1V
5.0V 3
—
—
—
—
—
1.0V
Open-Circuit 2
10V
—
–100μA
Notes:
1. The
Remote On/Off
control uses –V
in
(pin 17) as its ground
reference. All voltages specified are with respect to –V
in
.
2. Use an open-collector device (preferably a discrete
transistor) for the
Remote On/Off
input. Do not connect a
pull-up resistor directly to pin 11.
3. The
Remote On/Off
pin may be controlled with devices that have
a totem-pole output providing that a blocking diode is
used (See Figure 1). The blocking diode is required to
prevent current from being injected into On/Off control
pin.
Note: For TTL devices a pull-up may be required on the
cathode side of the blocking diode. This is to guarantee a
minimum enable voltage at pin 11 (See Figure 1).
4. The PT4210 converters incorporate an “Under-Voltage
Lockout” (UVLO). The UVLO will keep the module off
when the input voltage to the converter is low, regardless of
the state of the
Remote On/Off
control. Table 2 gives the
UVLO input voltage thresholds.
Table 2; UVLO Thresholds
4
Figure 1
Turn-On Time:
In the circuit of Figure 1, turning Q
1
on applies a
low-voltage to pin 11 and disables the converter output.
Correspondingly, turning Q
1
off allows pin 11
to be pulled
high by an internal pull-up resistor. The converter produces a
regulated output voltage within 50ms. Although the rise-
time of the output is short (<1ms), the delay time will vary
depending upon the input voltage and the module’s internal
timing. Figure 2 shows shows an example of the output
response for a PT4213 (5.0V), following the turn-off of
Q
1
at time t =0. The waveform was measured with a 48Vdc
input voltage, and 1.2Adc resistive load.
Figure 2
R1
10k
Q1
BSS138
+V
o
-V
o
+V
in
-V
in
Vdd
1 =OFF
Note 1
U1a
Note 1
Note 1
D1
1N4148
#
#
or similar low-leakage PIN diode
PT4210
+Vout
-Vout
+Vin
-Vin
Remote
On/Off*
11
17
18
1
2
Series
V
in
Range
UVLO Threshold
PT4210
38 – 75V
36V ±2V
0
5
10
15
20
25
30
time (milli-secs)
V
O
(2V/Div)
delay time
相關PDF資料 |
PDF描述 |
|---|---|
| PT4221 | 20V Single N-Channel HEXFET Power MOSFET in a D-Pak package; A IRFR3706 with Standard Packaging |
| PT4221A | 20V Single N-Channel HEXFET Power MOSFET in a D-Pak package; A IRFR3706 with Tape and Reel Packaging |
| PT4221C | 20V Single N-Channel HEXFET Power MOSFET in a D-Pak package; A IRFR3706 with Tape and Reel Left Packaging |
| PT4221N | Analog IC |
| PT4222 | 20V Single N-Channel HEXFET Power MOSFET in a D-Pak package; A IRFR3706 with Tape and Reel Right Packaging |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PT4214A | 功能描述:DC/DC轉換器 12Vout 7W 48V-Input Iso DC/DC Converter RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
| PT4214C | 功能描述:DC/DC轉換器 12Vout 7W 48V-Input Iso DC/DC Converter RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
| PT4220 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:10-W Low-Profile 48V-Input Isolated DC/DC Converter |
| PT4221 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:1.8Vout 5W 48V-Input Isolated DC/DC Converter |
| PT4221A | 功能描述:DC/DC轉換器 1.8Vout 5W 48V-Input Iso DC/DC Converter RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
發布緊急采購，3分鐘左右您將得到回復。