參數資料
型號： PSD935F3V-15MI
廠商： 意法半導體
英文描述： Configurable Memory System on a Chip for 8-Bit Microcontrollers
中文描述： 在8片位微控制器可配置存儲系統
文件頁數： 50/91頁
文件大?。?/td> 488K
代理商： PSD935F3V-15MI
PSD935G2
PSD9XX Family
49
The
PSD935G2
Functional
Blocks
(cont.)
9.4.2.4 Address In Mode
For microcontrollers that have more than 16 address lines, the higher addresses can be
connected to Ports A, B, C, D or F and are routed as inputs to the PLDs. The address
input can be latched by the address strobe (ALE/AS). Any input that is included in the
DPLD equations for the Main Flash, Boot Flash, or SRAM is considered to be an address
input.
9.4.2.5 Data Port Mode
Port F can be used as a data bus port for a microcontroller with a non-multiplexed
address/data bus. The Data Port is connected to the data bus of the microcontroller. The
general I/O functions are disabled in Port F if the port is configured as Data Port. Data Port
Mode is automatically configured in PSDsoft when a non-multiplexed bus MCU is selected.
9.4.2.3 Address Out Mode
For microcontrollers with a multiplexed address/data bus, Address Out Mode can be used
to drive latched addresses onto the port pins. These port pins can, in turn, drive external
devices. Either the output enable or the corresponding bits of both the Direction Register
and Control Register must be set to a ‘1’ for pins to use Address Out Mode. This must be
done by the MCU at run-time. See Table 18 for the address output pin assignments on
Ports E, F and F for various MCUs.
Note:
Do not drive address lines with Address Out Mode to an external memory device if
it is intended for the MCU to boot from the external device. The MCU must first boot from
PSD memory so the Direction and Control register bits can be set.
MCU
Port E (3:0)
Port E (7:4)
Port F (3:0)
Port F (7:4)
Port G (3:0)
Port G (7:4)
80C51XA
N/A
*
Addr (7:4)
N/A
*
Addr (7:4)
Addr (11:8)
N/A
80C251
(Page Mode)
N/A
N/A
N/A
N/A
Addr (11:8)
Addr (15:12)
All Other
Eight-Bit
Multiplexed
Addr (3:0)
Addr (7:4)
Addr (3:0)
Addr (7:4)
Addr (3:0)
Addr (7:4)
8-Bit
Non-Mux
Bus
N/A
N/A
N/A
N/A
Addr (3:0)
Addr (7:4)
Table 18. I/OPort Latched Address Output Assignments
相關PDF資料
PDF描述
PSD935F3V-15U Configurable Memory System on a Chip for 8-Bit Microcontrollers
PSD935F3V-15UI Configurable Memory System on a Chip for 8-Bit Microcontrollers
FS7VS-5 Nch POWER MOSFET HIGH-SPEED SWITCHING USE
FS8160 1.1 GHz/1.1 GHz Dual Phase-locked Loop IC
FS8853-13PI 300mA LDO Linear Regulator
相關代理商/技術參數
參數描述
PSD935G2-90U 功能描述:SPLD - 簡單可編程邏輯器件 TQFP-80 5V 4M 90N RoHS:否 制造商:Texas Instruments 邏輯系列:TICPAL22V10Z 大電池?cái)?shù)量:10 最大工作頻率:66 MHz 延遲時間:25 ns 工作電源電壓:4.75 V to 5.25 V 電源電流:100 uA 最大工作溫度:+ 75 C 最小工作溫度:0 C 安裝風格:Through Hole 封裝 / 箱體:DIP-24
PSD935G2V-90U 功能描述:SPLD - 簡單可編程邏輯器件 U 511-PSD835G2V-90U RoHS:否 制造商:Texas Instruments 邏輯系列:TICPAL22V10Z 大電池?cái)?shù)量:10 最大工作頻率:66 MHz 延遲時間:25 ns 工作電源電壓:4.75 V to 5.25 V 電源電流:100 uA 最大工作溫度:+ 75 C 最小工作溫度:0 C 安裝風格:Through Hole 封裝 / 箱體:DIP-24
PSD954F2-90J 功能描述:SPLD - 簡單可編程邏輯器件 U 511-PSD854F2-90J RoHS:否 制造商:Texas Instruments 邏輯系列:TICPAL22V10Z 大電池?cái)?shù)量:10 最大工作頻率:66 MHz 延遲時間:25 ns 工作電源電壓:4.75 V to 5.25 V 電源電流:100 uA 最大工作溫度:+ 75 C 最小工作溫度:0 C 安裝風格:Through Hole 封裝 / 箱體:DIP-24
PSD954F2-90M 功能描述:SPLD - 簡單可編程邏輯器件 U 511-PSD854F2-90M RoHS:否 制造商:Texas Instruments 邏輯系列:TICPAL22V10Z 大電池?cái)?shù)量:10 最大工作頻率:66 MHz 延遲時間:25 ns 工作電源電壓:4.75 V to 5.25 V 電源電流:100 uA 最大工作溫度:+ 75 C 最小工作溫度:0 C 安裝風格:Through Hole 封裝 / 箱體:DIP-24
PSD954F2V-90J 功能描述:SPLD - 簡單可編程邏輯器件 5.0V 2M 90ns RoHS:否 制造商:Texas Instruments 邏輯系列:TICPAL22V10Z 大電池?cái)?shù)量:10 最大工作頻率:66 MHz 延遲時間:25 ns 工作電源電壓:4.75 V to 5.25 V 電源電流:100 uA 最大工作溫度:+ 75 C 最小工作溫度:0 C 安裝風格:Through Hole 封裝 / 箱體:DIP-24
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*