• 參數資料
    型號: PSD9134V70MIT
    廠商: 意法半導體
    英文描述: Flash In-System Programmable ISP Peripherals For 8-bit MCUs
    中文描述: Flash在系統可編程ISP的外設的8位微控制器
    文件頁數: 70/110頁
    文件大?。?/td> 1737K
    代理商: PSD9134V70MIT
    PSD813F2, PSD833F2, PSD834F2, PSD853F2, PSD854F2
    70/110
    JTAG Extensions
    TSTAT and TERR are two JTAG extension signals
    enabled by an “ISC_ENABLE” command received
    over the four standard JTAG signals (TMS, TCK,
    TDI, and TDO). They are used to speed Program
    and Erase cycles by indicating status on PSD sig-
    nals instead of having to scan the status out seri-
    ally using the standard JTAG channel. See
    Application Note
    AN1153
    .
    TERR indicates if an error has occurred when
    erasing a sector or programming a byte in Flash
    memory. This signal goes Low (active) when an
    Error condition occurs, and stays Low until an
    “ISC_CLEAR” command is executed or a chip Re-
    set (RESET) pulse is received after an
    “ISC_DISABLE” command.
    TSTAT behaves the same as Ready/Busy de-
    scribed in the section entitled
    Ready/Busy
    (PC3), page 20
    . TSTAT is High when the PSD de-
    vice is in READ Mode (primary and secondary
    Flash memory contents can be read). TSTAT is
    Low when Flash memory Program or Erase cycles
    are in progress, and also when data is being writ-
    ten to the secondary Flash memory.
    TSTAT and TERR can be configured as open-
    drain type signals during an “ISC_ENABLE” com-
    mand. This facilitates a wired-OR connection of
    TSTAT signals from multiple PSD devices and a
    wired-OR connection of TERR signals from those
    same devices. This is useful when several PSD
    devices are “chained” together in a JTAG environ-
    ment.
    Security and Flash memory Protection
    When the security bit is set, the device cannot be
    read on a Device Programmer or through the
    JTAG Port. When using the JTAG Port, only a Full
    Chip Erase command is allowed.
    All other Program, Erase and Verify commands
    are blocked. Full Chip Erase returns the part to a
    non-secured blank state. The Security Bit can be
    set in PSDsoft Express Configuration.
    All primary and secondary Flash memory sectors
    can individually be sector protected against era-
    sures. The sector protect bits can be set in PSD-
    soft Express Configuration.
    Table 34. JTAG Port Signals
    Port C Pin
    JTAG Signals
    Description
    PC0
    TMS
    Mode Select
    PC1
    TCK
    Clock
    PC3
    TSTAT
    Status
    PC4
    TERR
    Error Flag
    PC5
    TDI
    Serial Data In
    PC6
    TDO
    Serial Data Out
    相關PDF資料
    PDF描述
    PSD8334V70MIT Flash In-System Programmable ISP Peripherals For 8-bit MCUs
    PSD8544V90JT Flash In-System Programmable ISP Peripherals For 8-bit MCUs
    PSD814F4V-15 Flash In-System Programmable (ISP) Peripherals for 8-bit MCUs, 5V
    PSD834F4V-15 Flash In-System Programmable (ISP) Peripherals for 8-bit MCUs, 5V
    PSD854F4V-15 Flash In-System Programmable (ISP) Peripherals for 8-bit MCUs, 5V
    相關代理商/技術參數
    參數描述
    PSD9134V70MT 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash In-System Programmable ISP Peripherals For 8-bit MCUs
    PSD9134V90JIT 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash In-System Programmable ISP Peripherals For 8-bit MCUs
    PSD9134V90JT 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash In-System Programmable ISP Peripherals For 8-bit MCUs
    PSD9134V90MIT 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash In-System Programmable ISP Peripherals For 8-bit MCUs
    PSD9134V90MT 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash In-System Programmable ISP Peripherals For 8-bit MCUs