參數資料
      型號： PSD4135G2V-C-70JI
      廠商： 意法半導體
      英文描述： Flash In-System-Programmable Peripherals for 16-Bit MCUs
      中文描述： Flash在系統可編程外設的16位微控制器
      文件頁數： 20/93頁
      文件大?。?/td> 503K
      代理商： PSD4135G2V-C-70JI
      Preliminary Information
      PSD4000 Series
      17
      FS0-7
      or
      CSBOOT0-3
      Instruction
      (Note 14)
      Cycle 1 Cycle 2 Cycle 3
      Cycle 4
      Cycle5
      Cycle 6
      Cycle 7
      Read (Note 5)
      1
      “Read”
      RA RD
      Read Main Flash ID
      (Note 6)
      1
      AAh
      55h
      90h
      “Read”
      ID
      @XX02h
      @XAAAh @X554h @XAAAh
      Read Sector Protection
      (Notes 6,8,13)
      1
      AAh
      55h
      90h
      “Read”
      @XAAAh @X554h @XAAAh 00h or 01h
      @XX04h
      Program a Flash Word
      1
      AAh
      55h
      A0h
      PD@PA
      @XAAAh @X554h @XAAAh
      Erase One Flash Sector
      1
      AAh
      55h
      80h
      AAh
      55h
      30h
      @SA
      30h
      @XAAAh @X554h @XAAAh
      @XAAAh
      @X554h
      @next SA
      (Note 7)
      Erase Flash Block
      (Bulk Erase)
      1
      AAh
      55h
      80h
      AAh
      55h
      10h
      @XAAAh @X554h @XAAAh
      @XAAAh
      @X554h
      @XAAAh
      Suspend Sector Erase
      (Note 11)
      1
      B0h
      @xxxh
      Resume Sector Erase
      (Note 12)
      1
      30h
      @xxxh
      Reset (Note 6)
      1
      F0 @ any
      address
      Unlock Bypass
      1
      AAh
      55h
      20h
      @XAAAh @X554h @XAAAh
      Unlock Bypass Program
      (Note 9)
      1
      A0h
      PD@PA
      @XXXXh
      Unlock Bypass Reset
      (Note 10)
      1
      90h
      00h
      @XXXXh @XXXXh
      Table 8. Instructions
      X
      RA = Address of the memory location to be read.
      RD = Data read from location RA during read operation.
      PA = Address of the memory location to be programmed. Addresses are latched on the falling edge of the WR#
      (CNTL0) pulse. PA is an even address for PSD in word programming mode.
      PD = Data (word) to be programmed at location PA. Data is latched on the rising edge of WR# (CNTL0) pulse.
      SA = Address of the sector to be erased or verified. The chip select (FS0-7 or CSBOOT0-3) of the sector to be
      erased must be active (high).
      = Don’t Care. “xxxh” address in the above table must be an even address.
      NOTES:
      1.
      All bus cycles are write bus cycle except the ones with the “read” label.
      2.
      All values are in hexadecimal.
      3.
      FS0-7 and CSBOOT0-3 are active high and are defined in PSDsoft.
      4.
      Only Address bits A11-A0 are used in Instruction decoding.
      5.
      No unlock or command cycles required when device is in read mode.
      6.
      The Reset command is required to return to the read mode after reading the Flash ID, Sector Protect status
      or if DQ5 (DQ13) goes high.
      7.
      Additional sectors to be erased must be entered within 80μs.
      8.
      The data is 00h for an unprotected sector and 01h for a protected sector. In the fourth cycle, the sector chip
      select is active and (A1 = 1, A0 = 0).
      9.
      The Unlock Bypass command is required prior to the Unlock Bypass Program command.
      10. The Unlock Bypass Reset command is required to return to reading array data when the device is in the
      Unlock Bypass mode.
      11. The system may read and program functions in non-erasing sectors, read the Flash ID or read the Sector
      Protect status, when in the Erase Suspend mode. The erase Suspend command is valid only during a sector
      erase operation.
      12. The Erase Resume command is valid only during the Erase Suspend mode.
      13. The MCU cannot invoke these instructions while executing code from the same Flash memory for which the
      instruction is intended. The MCU must fetch, for example, codes from the Secondary Flash memory when
      reading the Sector Protection Status of the main Flash.
      14. All write bus cycles in an instruction are byte write to even address (XA4Ah or X554h). Flash Programming
      bys cycle is writing a word to even address.
      The
      PSD4000
      Functional
      Blocks
      (cont.)
      相關PDF資料
      PDF描述
      PSD4135G3-90U Ceramic Commercial-Off-The-Shelf Surface Mount Capacitors (COTS); Capacitance [nom]: 2200pF; Working Voltage (Vdc)[max]: 25V; Capacitance Tolerance: +/-5%; Dielectric: Multilayer Ceramic; Temperature Coefficient: C0G (NP0); Lead Style: Surface Mount Chip; Lead Dimensions: 0805; Termination: Solder (SnPb) Plated Nickel Barrier; Body Dimensions: 0.079" x 0.049"; Container: Bulk; Features: MIL-PRF-55681; Unmarked
      PSD4135G3-90UI Flash In-System-Programmable Peripherals for 16-Bit MCUs
      PSD4135G3-A-12JI Flash In-System-Programmable Peripherals for 16-Bit MCUs
      PSD4135G3-A-12M Flash In-System-Programmable Peripherals for 16-Bit MCUs
      PSD4135G3-A-12MI Flash In-System-Programmable Peripherals for 16-Bit MCUs
      相關代理商/技術參數
      參數描述
      PSD4135G2V-C-70M 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash In-System-Programmable Peripherals for 16-Bit MCUs
      PSD4135G2V-C-70MI 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash In-System-Programmable Peripherals for 16-Bit MCUs
      PSD4135G2V-C-70U 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash In-System-Programmable Peripherals for 16-Bit MCUs
      PSD4135G2V-C-70UI 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash In-System-Programmable Peripherals for 16-Bit MCUs
      PSD4135G2V-C-90B81 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash In-System-Programmable Peripherals for 16-Bit MCUs
      發布緊急采購，3分鐘左右您將得到回復。

      采購需求

      (若只采購一條型號，填寫一行即可)

      發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

      發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

      *型號 *數量 廠商 批號 封裝
      添加更多采購

      我的聯系方式

      *
      *
      *