參數資料
型號: PSD412A1-20U
英文描述: 200V 100kRad Hi-Rel Single N-Channel SEE Hardened MOSFET in a TO-257AA package; JANS Certified device. Equivalent to IR Part Number IRHY57230CMSE
中文描述: 現場可編程外圍
文件頁數: 64/123頁
文件大?。?/td> 657K
代理商: PSD412A1-20U
PSD4XX Famly
61
9.4 Memory Block
The PSD4XX provides EPROM memory for code storage and SRAM memory for scratch
pad usage. Chip selects for the memory blocks come from the DPLD decoding logic and
are defined by the user in the PSDsoft Software. Figure 32 shows the organization of the
Memory Block.
The PSD4XX family uses Zero-power memory techniques that place memory into Standby
Mode between MCU accesses. The memory becomes active briefly after an address
transition, then delivers new data to the outputs, latches the outputs, and returns to standby.
This is done automatically and the designer has to do nothing special to benefit from this
feature. Both the EPROM and SRAM have this feature.
9.4.1 EPROM
The PSD4XX provides three EPROM densities: 256Kbit, 512Kbit, or 1Mbit. The EPROM
is divided into four 8K, 16K or 32K byte blocks. Each block has its own chip select signals
(ES0 – ES3). The EPROM can be configured as 32K x 8, 64K x 8 or 128K x 8 for
microcontrollers with an 8-bit data bus. For 16-bit data buses, the EPROM is configured as
16K x 16, 32K x 16 or 64K x 16.
9.4.2 SRAM
The SRAM has 16Kbits of memory, organized as 2K x 8 or 1K x 16. The SRAM is enabled
by chip select signal RS0 from the DPLD. The SRAM has a battery back-up (STBY) mode.
This back-up mode is invoked when the V
CC
voltage drops under the Vstdby voltage by
approximately 0.7 V. The Vstdby voltage is connected only to the SRAM and cannot be
lower than 2.7 volts.
9.4.3 Memory Select Map
The EPROM and SRAM chip select equations are defined in the ABEL file in terms of
address and other DPLD inputs. The memory space for the EPROM chip select
(ES0 – ES3) should not be larger than the EPROM block (8KB, 16KB, or 32KB) it is
selecting.
The following rules govern how the internal PSD4XX memory selects/space are defined:
J
The EPROM blocks address space cannot overlap
J
SRAM, internal I/O and Peripheral I/O space cannot overlap
J
SRAM, internal I/O and Peripheral I/O space can overlap EPROM space, with
priority given to SRAM or I/O. The portion of EPROM which is overlapped
cannot be accessed.
The Peripheral I/O space refers to memory space occupied by peripherals when Port A is
configured in the Peripheral I/O Mode.
The PSD4XX
Architecture
(cont.)
相關PDF資料
PDF描述
PSD413A1-15J Field-Programmable Peripheral
PSD413A1-15JI 60V 300kRad Hi-Rel Single N-Channel TID Hardened MOSFET in a 18-pin LCC package; JANS Certified version of the IRHE57034 with optional Total Dose Rating of 300kRads
PSD413A1-15LI 60V 300kRad Hi-Rel Single N-Channel TID Hardened MOSFET in a 18-pin LCC package; JANS Certified version of the IRHE57034 with optional Total Dose Rating of 1000kRads
PSD413A1-15U 150V 300kRad Hi-Rel Single N-Channel TID Hardened MOSFET in a Low-Ohmic TO-257AA package; Similar to IRHYB67134CM with optional Total Dose rating of 300KRads
PSD413A1-15UI Field-Programmable Peripheral
相關代理商/技術參數
參數描述
PSD412A1-20UI 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Field-Programmable Peripheral
PSD412A1-70J 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Field-Programmable Peripheral
PSD412A1-70U 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Field-Programmable Peripheral
PSD412A1-90J 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Field-Programmable Peripheral
PSD412A1-90U 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Field-Programmable Peripheral