- 您現在的位置：買賣IC網 > PDF目錄96788 > PS21352-N AC MOTOR CONTROLLER, 10 A, DMA35 PDF資料下載
參數資料
| 型號： | PS21352-N |
| 元件分類： | 運動控制電子 |
| 英文描述： | AC MOTOR CONTROLLER, 10 A, DMA35 |
| 文件頁數： | 9/9頁 |
| 文件大?。?/td> | 149K |
| 代理商： | PS21352-N |
MITSUBISHI SEMICONDUCTOR <Intelligent Power Module>
PS21352-N
TRANSFER-MOLD TYPE
INSULATED TYPE
Sep. 2001
Fig. 7 TYPICAL DIP-IPM APPLICATION CIRCUIT EXAMPLE
Note 1 : To prevent the input signals oscillation, an RC coupling at each input is recommended, and the wiring of each input should be as short
as possible (less than 2cm).
2: By virtue of integrating an application specific type HVIC inside the module, direct coupling to CPU terminals without any opto-coupler
or transformer isolation is possible.
3: FO output is open collector type. This signal line should be pulled up to the positive side of the 5V power supply with approximately
5.1k
resistance.
4: FO output pulse width should be decided by connecting an external capacitor between CFO and VNC terminals (CFO). (Example : CFO
= 22 nF
→ tFO = 1.8 ms (typ.))
5: Each input signal line should be pulled up to the positive side of the 5V power supply with approximately 4.7k
resistance (other RC
coupling circuits at each input may be needed depending on the PWM control scheme used and on the wiring impedances of the
system’s printed circuit board). Approximately a 0.22~2
F by-pass capacitor should be used across each power supply connection
terminals.
6: To prevent errors of the protection function, the wiring of A, B, C should be as short as possible.
7: In the recommended protection circuit, please select the R1C5 time constant in the range of 1.5~2
s.
8: Each capacitor should be put as nearby the terminals of the DIP-IPM as possible.
9: To prevent surge destruction, the wiring between the smoothing capacitor and the P&N1 terminals should be as short as possible. Ap-
proximately a 0.1~0.22
F snubber capacitor between the P&N1 terminals is recommended.
HO
DIP-IPM
C3
C2
C1
HO
IN
COM
UOUT
VOUT
WOUT
VNO
CFO
GND
F
o
WN
VN
VCC
C
B
A
C4(CFO)
CFO
R1
C5
CIN
N1
N
W
V
U
P
VS
VB
VCC
Fo
WN
VN
UN
UN
WP
VP
UP
VNC
VN1
VP1
HVIC1
HVIC2
HVIC3
LVIC
VWFS
VVFS
VUFS
VWFB
VVFB
VUFB
M
Shunt
resistor
The long wiring of GND might generate
noise on input signals and cause IGBT
to be malfunctioned.
If this wiring is too long, the SC level
fluctuation might be large and cause
SC malfunction.
If this wiring is too long,
short circuit might
be caused.
15V line
5V line
U
N
I
T
C
P
U
5V line
C1: Tight tolerance temp-compensated electrolytic type; C2,C3: 0.22~2
F R-category ceramic capacitor for noise filtering
相關PDF資料 |
PDF描述 |
|---|---|
| PS21445-E | AC MOTOR CONTROLLER, 40 A, DMA26 |
| PS21542-N | AC MOTOR CONTROLLER, 10 A, DMA35 |
| PS21552-G | AC MOTOR CONTROLLER, 10 A, DMA35 |
| PS21552-N | AC MOTOR CONTROLLER, 10 A, DMA35 |
| PS21553-N | AC MOTOR CONTROLLER, 20 A, DMA35 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PS21352-NP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:Generation DIP and Mini-DIP-IPM |
| PS21353-G | 制造商:Powerex Power Semiconductors 功能描述:MINI DIP-IPM |
| PS21353GP | 制造商:POWEREX 制造商全稱:Powerex Power Semiconductors 功能描述:Intellimoda?￠ Module |
| PS21353-GP | 功能描述:MOD IPM 600V 10A MINI-DIP RoHS:是 類別:半導體模塊 >> 功率驅動器 系列:Intellimod™ 標準包裝:15 系列:SPM® 類型:FET 配置:三相反相器 電流:1.8A 電壓:500V 電壓 - 隔離:1500Vrms 封裝/外殼:23-DIP 模塊 |
| PS21353-N | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:600V/10A low-loss 4th generation (planar) IGBT inverter bridge for 3 phase DC-to-AC power conversion. |
發布緊急采購，3分鐘左右您將得到回復。