- 您現在的位置：買賣IC網 > PDF目錄96787 > PS20341-G AC MOTOR CONTROLLER, 6 A, DMA35 PDF資料下載
參數資料
| 型號： | PS20341-G |
| 元件分類： | 運動控制電子 |
| 英文描述： | AC MOTOR CONTROLLER, 6 A, DMA35 |
| 文件頁數： | 9/9頁 |
| 文件大?。?/td> | 153K |
| 代理商： | PS20341-G |
MITSUBISHI SEMICONDUCTOR <Intelligent Power Module>
PS20341-G
TRANSFER-MOLD TYPE
INSULATED TYPE
Sep. 2001
HO
DIP-IPM
C1: Tight tolerance temp-compensated electrolytic type; C2,C3: 0.22~2
F R-category ceramic capacitor for noise filtering
C3
C2
C1
HO
IN
15V line
5V line
IN
COM
UOUT
VOUT
WOUT
VNO
CFO
GND
F
o
WN
VN
VCC
C
B
A
C4(CFO)
CFO
R1
C5
Shunt
resistor
CIN
N1
N
W
V
U
P
VS
VB
VCC
Fo
WN
VN
UN
UN
WP
VP
UP
VNC
VN1
VP1
VWFS
VVFS
VUFS
VWFB
VVFB
VUFB
M
C
P
U
N
I
T
The long wiring of GND might generate
noise on input signals and cause IGBT
to be malfunctioned.
If this wiring is too long, the SC level
fluctuation might be large and cause
SC malfunction.
If this wiring is too long,
short circuit might
be caused.
Fig. 7 TYPICAL DIP-IPM APPLICATION CIRCUIT EXAMPLE
Note 1 : To prevent the input signals oscillation, an RC coupling at each input is recommended, and the wiring of each input should be as short
as possible (less than 2cm).
2: By virtue of integrating an application specific type HVIC inside the module, direct coupling to CPU terminals without any opto-coupler
or transformer isolation is possible.
3: FO output is open collector type. This signal line should be pulled up to the positive side of the 5V power supply with approximately
5.1k
resistance.
4: FO output pulse width should be decided by connecting an external capacitor between CFO and VNC terminals (CFO). (Example : CFO
= 22 nF
→ tFO = 1.8 ms (typ.))
5: Each input signal line should be pulled up to the positive side of the 5V power supply with approximately 4.7k
resistance (other RC
coupling circuits at each input may be needed depending on the PWM control scheme used and on the wiring impedances of the
system’s printed circuit board). Approximately a 0.22~2
F by-pass capacitor should be used across each power supply connection
terminals.
6: To prevent errors of the protection function, the wiring of A, B, C should be as short as possible.
7: In the recommended protection circuit, please select the R1C5 time constant in the range of 1.5~2
s.
8: Each capacitor should be put as nearby the terminals of the DIP-IPM as possible.
9: To prevent surge destruction, the wiring between the smoothing capacitor and the P&N1 terminals should be as short as possible. Ap-
proximately a 0.1~0.22
F snubber capacitor between the P&N1 terminals is recommended.
相關PDF資料 |
PDF描述 |
|---|---|
| PS20351-G | AC MOTOR CONTROLLER, 6 A, DMA35 |
| PS21204 | AC MOTOR CONTROLLER, 15 A, PDIP26 |
| PS21212 | AC MOTOR CONTROLLER, 5 A, PDIP26 |
| PS21244-E | AC MOTOR CONTROLLER, 30 A, DMA26 |
| PS21245-EP | AC MOTOR CONTROLLER, 40 A, UFM26 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PS20341-GP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:Generation DIP and Mini-DIP-IPM |
| PS20341-NP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:Generation DIP and Mini-DIP-IPM |
| PS20351-G | 制造商:POWEREX 制造商全稱:Powerex Power Semiconductors 功能描述:Intellimod⑩ Module Dual-In-Line Intelligent Power Module 3 Amperes/500 Volts |
| PS20351-GP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:Generation DIP and Mini-DIP-IPM |
| PS20351-N | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:TRANSFER-MOLD TYPE INSULATED TYPE |
發布緊急采購，3分鐘左右您將得到回復。