- 您現在的位置：買賣IC網 > PDF目錄370018 > PROGRAMMING Programming the M16C/62 Flash in Asynchronous Serial ModeApplication Note 214K/JUL.07.03 PDF資料下載
參數資料
| 型號： | PROGRAMMING |
| 英文描述： | Programming the M16C/62 Flash in Asynchronous Serial ModeApplication Note 214K/JUL.07.03 |
| 中文描述： | 異步串行編程ModeApplication注意214K/JUL.07.03的雙隨機PWM閃光 |
| 文件頁數： | 4/7頁 |
| 文件大?。?/td> | 214K |
| 代理商： | PROGRAMMING |
M16C/62
Programming the M16C/62 Flash in Asynchronous Serial Mode
Input the path and file name in the FilePath field box and the ID code in the ID field box. Selecting the Refer
button will open a browse window to locate the file on your PC. If the ID file is in the same folder (refer to the
FlashStart manual), the ID code is loaded when the file is selected. If there is no ID file, a warning message will
be shown that indicates the ID file cannot be found. Select "OK" in the warning box and enter the correct ID bytes
in the ID boxes or ‘FF’ or ‘00’ in the boxes if there is no ID code being used.
Figure 4 ID Check Dialog Box
Once the ID code has been entered, selecting the OK button will start the ID check and opens the FlashStart
Programmer window. This allows the device commands to be executed. If an ID matching error occurs, the
FlashStart Programmer window will still open; however, the user will be unable to execute the commands. In this
case, recheck the ID code.
Selecting the Cancel button will open the FlashStart Programmer window without running an ID check. The
FlashStart allows device commands to be used with cleared flash without performing an ID check.
4.3 FlashStart Programming Window
The FlashStart Programming window executes device commands. If the flash MCU is cleared, the device
commands can be used without running an ID check. However, if the flash is written, only the Load (ID), Status,
and Setting commands can be used until the ID check is run. Once the correct ID check is completed, all of the
following commands are available:
Load (ID)
Selects a file and checks the ID code.
Blank
Checks if a selected area of Flash ROM is blank.
Read
Compares the contents of the Flash ROM with the selected file.
Status
Displays the current status of the Flash ROM.
REU05B0013-0100Z
June 2003
Page 4 of 6
相關PDF資料 |
PDF描述 |
|---|---|
| PRS07 | Fast soft-recovery rectifiers |
| PRS07D | Fast soft-recovery rectifiers |
| PRS07G | Fast soft-recovery rectifiers |
| PRS07J | Fast soft-recovery rectifiers |
| PRS28G | Packet Routing Switch For Multigigabit-Per-Port Switch Solution(網絡通信用信息包通路轉換開關) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PROGSHIELD | 功能描述:PROGRAMMER SHIELD 制造商:particle industries, inc. 系列:- 零件狀態:在售 類型:編程器 配套使用產品/相關產品:Photon 內容:板 標準包裝:1 |
| PROG-WIN2 | 功能描述:LABEL SOFTWARE WINDOWS ADV 3.5" RoHS:否 類別:編程器，開發系統 >> 過時/停產零件編號 系列:- 標準包裝:1 系列:- 傳感器類型:CMOS 成像，彩色（RGB） 傳感范圍:WVGA 接口:I²C 靈敏度:60 fps 電源電壓:5.7 V ~ 6.3 V 嵌入式:否 已供物品:成像器板 已用 IC / 零件:KAC-00401 相關產品:4H2099-ND - SENSOR IMAGE WVGA COLOR 48-PQFP4H2094-ND - SENSOR IMAGE WVGA MONO 48-PQFP |
| PROGWIN2CD | 制造商:Panduit Corp 功能描述:Unspecified Tools & Accessories SOFTWARE |
| PROG-WIN2CD | 功能描述:CD ROM WINDOWS PAN-MARK LABELING RoHS:否 類別:編程器，開發系統 >> 軟件 系列:- 標準包裝:1 系列:ISE® 設計套件 類型:訂閱 適用于相關產品:Xilinx FPGAs 其它名稱:Q4986209T1081384 |
| PROHDCART | 制造商:OMNIMOUNT 功能描述:FLAT PANEL MOBILE CART FITS 37 IN - 55 IN FLAT PANELS |
發布緊急采購，3分鐘左右您將得到回復。