- 您現在的位置：買賣IC網 > PDF目錄69082 > PQ60015ETL45NNS-G (SYNQOR INC) 1-OUTPUT 67.5 W DC-DC REG PWR SUPPLY MODULE PDF資料下載
參數資料
| 型號： | PQ60015ETL45NNS-G |
| 廠商： | SYNQOR INC |
| 元件分類： | 電源模塊 |
| 英文描述： | 1-OUTPUT 67.5 W DC-DC REG PWR SUPPLY MODULE |
| 封裝： | ROHS COMPLIANT, EIGHTH BRICK PACKAGE-8 |
| 文件頁數： | 3/14頁 |
| 文件大小： | 2155K |
| 代理商： | PQ60015ETL45NNS-G |
35-75 V
1.5 V
45 A
PQ60015ETL45
Product # PQ60015ETL45
Phone 1-888-567-9596
www.synqor.com
Doc.# 005-0005082 Rev. A
11/19/08
Page 11
Input:
Output:
Current:
Part no.:
35-75 V
1.5 V
45 A
PQ60015ETL45
Technical Specification
OUTPUT VOLTAGE TRIM (Pin 6): The TRIM input permits
the user to adjust the output voltage across the sense leads up
or down according to the trim range specifications.
To decrease the output voltage, the user should connect a
resistor between Pin 6 and Pin 5 (SENSE(-) input). For a desired
decrease of the nominal output voltage, the value of the resistor
should be
Rtrim-down =
( 511 ) - 10.22 (kW)
D%
where
D% = Vnominal – Vdesired x 100%
Vnominal
To increase the output voltage, the user should connect a
resistor between Pin 6 and Pin 7 (SENSE(+) input). For a desired
increase of the nominal output voltage, the value of the resistor
should be
Figure C graphs the relationship between the trim resistor value
and Rtrim-up and Rtrim-down, showing the total range the
output voltage can be trimmed up or down.
Figure C: Trim Graph for 1.8Vout module
Note: the TRIM feature does not affect the voltage at which the
output over-voltage protection circuit is triggered. Trimming the
output voltage too high may cause the over-voltage protection
circuit to engage, particularly during transients.
It is not necessary for the user to add capacitance at the Trim
pin. The node is internally bypassed to eliminate noise.
Total DC Variation of Vout: For the converter to meet its full
specifications, the maximum variation of the DC value of Vout,
due to both trimming and remote load voltage drops, should
not be greater than that specified for the output voltage trim
range.
PROTECTION FEATURES
Input Under-Voltage Lockout: The converter is designed
to turn off when the input voltage is too low, helping avoid an
input system instability problem, described in more detail in the
application note titled “Input System Instability”. The lockout
circuitry is a comparator with DC hysteresis. When the input
voltage is rising, it must exceed the typical Turn-On Voltage
Threshold value (listed on the specification page) before the
converter will turn on. Once the converter is on, the input
voltage must fall below the typical Turn-Off Voltage Threshold
value before the converter will turn off.
Output Current Limit: Once the output current reaches the
current-limit inception point, the converter will decrease the
output voltage as the output current increases. However, once
the impedance of the short across the output is small enough
to make the output voltage drop below the specified Output DC
Current-Limit Shutdown Voltage, the converter turns off (see
Figure 23).
The converter then enters a “hiccup mode” where it repeatedly
turns on and off at a 5 Hz (nominal) frequency with a 5% duty
cycle until the short circuit condition is removed. This prevents
excessive heating of the converter or the load board.
Output Over-Voltage Limit: If the voltage across the output
pins exceeds the Output Over-Voltage Protection threshold, the
converter will immediately stop switching. This prevents damage
to the load circuit due to 1) excessive series resistance in output
current path from converter output pins to sense point, 2) a
release of a short-circuit condition, or 3) a release of a current
limit condition. Load capacitance determines exactly how high
the output voltage will rise in response to these conditions. After
200 ms the converter will automatically restart.
Over-Temperature Shutdown: A temperature sensor on
the converter senses the average temperature of the module.
The thermal shutdown circuit is designed to turn the converter
off when the temperature at the sensed location reaches the
Over-Temperature Shutdown value. It will allow the converter
to turn on again when the temperature of the sensed location
falls by the amount of the Over-Temperature Shutdown Restart
Hysteresis value.
Rtrim-
up
(kW)
)
where
VOUT = Nominal Output Voltage
=
(
_ 511 _ 10.22
5.11VOUT(100+D%)
1.225
D%
1
10
100
1,000
10,000
0
2
4
6
8
10
12
14
16
18
20
Trim
Resistance
(kOhms)
% increase Vout
% decrease Vout
相關PDF資料 |
PDF描述 |
|---|---|
| PQ60015ETL45PRS-G | 1-OUTPUT 67.5 W DC-DC REG PWR SUPPLY MODULE |
| PQ60015HPAA0NNF-G | 1-OUTPUT 150 W DC-DC REG PWR SUPPLY MODULE |
| PQ60015HPAA0NRS-G | 1-OUTPUT 150 W DC-DC REG PWR SUPPLY MODULE |
| PQ60015HPAA0PNS-G | 1-OUTPUT 150 W DC-DC REG PWR SUPPLY MODULE |
| PQ60015HPAA0PKF-G | 1-OUTPUT 150 W DC-DC REG PWR SUPPLY MODULE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PQ60015HPAA0 | 制造商:SYNQOR 制造商全稱:SYNQOR 功能描述:Half-brick DC/DC Converter |
| PQ60015HPAA0NKF-G | 制造商:SYNQOR 制造商全稱:SYNQOR 功能描述:Half-brick DC/DC Converter |
| PQ60015HPAA0NKS-G | 制造商:SYNQOR 制造商全稱:SYNQOR 功能描述:Half-brick DC/DC Converter |
| PQ60015HPAA0NNF-G | 制造商:SYNQOR 制造商全稱:SYNQOR 功能描述:Half-brick DC/DC Converter |
| PQ60015HPAA0NNS-G | 制造商:SYNQOR 制造商全稱:SYNQOR 功能描述:Half-brick DC/DC Converter |
發布緊急采購，3分鐘左右您將得到回復。