- 您現在的位置：買賣IC網 > PDF目錄368095 > PPC405GP-3BE133CZ (APPLIEDMICRO INC) Power PC 405GP Embedded Processor PDF資料下載
參數資料
| 型號： | PPC405GP-3BE133CZ |
| 廠商： | APPLIEDMICRO INC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | Power PC 405GP Embedded Processor |
| 中文描述： | 32-BIT, 133 MHz, RISC PROCESSOR, PBGA456 |
| 封裝： | 35 X 35 MM, PLASTIC, EBGA-456 |
| 文件頁數： | 34/59頁 |
| 文件大?。?/td> | 782K |
| 代理商： | PPC405GP-3BE133CZ |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁當前第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁
405GP – Power PC 405GP Embedded Processor
34
AMCC
Revision 2.03 – September 7, 2007
Data Sheet
Pull-Up and Pull-Down Resistors
Pull-up and pull-down resistors are used for strapping during reset and to retain unused or undriven inputs in an
appropriate state. The recommended pull-up value of 3k
Ω
to +3.3V (10k
Ω
to +5V can be used on 5V tolerant I/Os)
and pull-down value of 1k
Ω
to GND, applies only to individually terminated signals. To prevent possible damage to
the device, I/Os capable of becoming outputs
must never
be tied together and terminated through a common
resistor.
If your system-level test methodology permits, input-only signals can be connected together and terminated
through either a common resistor or directly to +3.3V or GND. When a resistor is used, its value must ensure that
the grouped I/Os reach a valid logic zero or logic one state when accounting for the total input current into the
PPC405GP.
Unused I/Os
Termination of some pins may be necessary when they are unused. Although the PPC405GP requires only the
pull-up and pull-down terminations as specified in the “Signal Functional Description” on page 35, good design
practice is to terminate all unused inputs or to configure I/Os such that they always drive. If unused, the peripheral,
SDRAM, and PCI buses should be configured and terminated as follows:
Peripheral interface—PerAddr0:31, PerData0:31, and all of the control signals are driven by default. Terminate
PerReady high and PerError low.
SDRAM—Program SDRAM0_CFG[EMDULR]=1 and SDRAM0_CFG[DCE]=1. This causes the PPC405GP to
actively drive all of the SDRAM address, data, and control signals.
PCI—The PCI pull-up requirements given in the Signal Functional Description apply only when the PCI
interface is being used. When the PCI bridge is unused, configure the PCI controller to park on the bus and
actively drive PCIAD31:0, PCIC3:0[BE3:0], and the remaining PCI control signals by doing the following:
- Strap the PPC405GP to disable the internal PCI arbiter and to operate the PCI interface in synchronous
mode.
- Individually connect PCISErr, PCIPErr, PCITRDY, and PCIStop through 3k
Ω
resistors to +3.3V.
- Terminate PCIReq1:5 to +3.3V.
- Terminate PCIReq0[Gnt] to GND.
External Bus Control Signals
All peripheral bus control signals (PerCS0:7, PerR/W, PerWBE0:3, PerOE, PerWE, PerBLast, HoldAck, ExtAck)
are set to the high-impedance state when ExtReset=0. In addition, as detailed in the
PowerPC 405GP Embedded
Processor User’s Manual
, the peripheral bus controller can be programmed via EBC0_CFG to float some of these
control signals between transactions and/or when an external master owns the peripheral bus. As a result, a pull-
up resistor should be added to those control signals where an undriven state may affect any devices receiving that
particular signal.
The following table lists all of the I/O signals provided by the PPC405GP. Please refer to “Signals Listed
Alphabetically” on page 17 for the pin number to which each signal is assigned.
相關PDF資料 |
PDF描述 |
|---|---|
| PPC405GP-3BE200C | Power PC 405GP Embedded Processor |
| PPC405GP-3BE200CZ | Power PC 405GP Embedded Processor |
| PPC405GP-3BE266C | Power PC 405GP Embedded Processor |
| PPC405GP-3BE266CZ | Power PC 405GP Embedded Processor |
| PPC405GP-3DE133C | Power PC 405GP Embedded Processor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PPC405GP-3BE200C | 制造商:AppliedMicro 功能描述:MPU 405GP RISC 32-Bit 0.25um 200MHz 3.3V 456-Pin EBGA Tray |
| PPC405GP-3BE200CZ | 制造商:AppliedMicro 功能描述:MPU 405GP RISC 32-Bit 0.25um 200MHz 3.3V 456-Pin EBGA T/R |
| PPC405GP-3BE266C | 制造商:AppliedMicro 功能描述:MPU 405GP RISC 32-Bit 0.25um 266MHz 3.3V 456-Pin EBGA Tray |
| PPC405GP-3BE266CZ | 制造商:AMCC 制造商全稱:Applied Micro Circuits Corporation 功能描述:Power PC 405GP Embedded Processor |
| PPC405GP-3DE133C | 制造商:AMCC 制造商全稱:Applied Micro Circuits Corporation 功能描述:Power PC 405GP Embedded Processor |
發布緊急采購，3分鐘左右您將得到回復。