- 您現在的位置：買賣IC網 > PDF目錄98054 > PM6670ATR (STMICROELECTRONICS) 1.4 A SWITCHING CONTROLLER, QCC24 PDF資料下載
參數資料
| 型號： | PM6670ATR |
| 廠商： | STMICROELECTRONICS |
| 元件分類： | 穩壓器 |
| 英文描述： | 1.4 A SWITCHING CONTROLLER, QCC24 |
| 封裝： | 4 X 4 MM, LEAD FREE, VFQFN-24 |
| 文件頁數： | 35/55頁 |
| 文件大?。?/td> | 849K |
| 代理商： | PM6670ATR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁當前第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁
Application information
PM6670
40/53
8.1.1
Inductor selection
Once the switching frequency has been defined, the inductance value depends on the
desired inductor ripple current. Low inductance value means great ripple current that brings
poor efficiency and great output noise. On the other hand a great current ripple is desirable
for fast transient response when a load step is applied.
High inductance brings higher efficiency, but the transient response is critical, especially if
VINmin - VOUT is small. Moreover a minimum output ripple voltage is necessary to assure
system stability and jitter-free operations (see Output capacitor selection paragraph). The
product of the output capacitor's ESR multiplied by the inductor ripple current must be taken
into consideration. A good trade-off between the transient response time, the efficiency, the
cost and the size is choosing the inductance value in order to maintain the inductor ripple
current between 20% and 50% (usually 40%) of the maximum output current.
The maximum inductor ripple current,
I
L,MAX , occurs at the maximum input voltage.
Given these considerations, the inductance value can be calculated with the following
expression:
Equation 29
where fSW is the switching frequency, VIN is the input voltage, VOUT is the output voltage and
I
L is the inductor ripple current.
Once the inductor value is determined, the inductor ripple current is then recalculated:
Equation 30
The next step is the calculation of the maximum r.m.s. inductor current:
Equation 31
The inductor must have an r.m.s. current greater than IL,RMS in order to assure thermal
stability.
Then the calculation of the maximum inductor peak current follows:
Equation 32
IL,PEAK is important in inductor selection in term of its saturation current.
IN
OUT
L
OUT
IN
V
I
fsw
V
L
=
MAX
,
IN
OUT
MAX
,
IN
MAX
,
L
V
L
fsw
V
I
=
12
)
I
(
)
I
(
I
2
MAX
,
L
2
MAX
,
LOAD
RMS
,
L
+
=
2
I
MAX
,
L
MAX
,
LOAD
PEAK
,
L
+
=
相關PDF資料 |
PDF描述 |
|---|---|
| PM6670 | 1.4 A SWITCHING CONTROLLER, QCC24 |
| PM6675ASTR | 3 A SWITCHING CONTROLLER, QCC24 |
| PM6675AS | 3 A SWITCHING CONTROLLER, QCC24 |
| PM6675ATR | SWITCHING CONTROLLER, QCC24 |
| PM6675TR | SWITCHING CONTROLLER, QCC24 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PM6670S | 功能描述:DC/DC 開關控制器 DDR 2/3 Memory Pwr Cntrl RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| PM6670STR | 功能描述:DC/DC 開關控制器 Complete DDR2/3 Mem Pwr supply controllr RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| PM6670TR | 功能描述:直流/直流開關調節器 Complete DDR2/3 Mem Pwr supply controllr RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5 |
| PM6675 | 制造商:STMicroelectronics 功能描述: 制造商:STMicroelectronics 功能描述:LDO CNTRLR STDN 0.6V TO 3.3V/1.5V 24PIN VFQFPN - Rail/Tube |
| PM6675AS | 功能描述:DC/DC 開關控制器 DDR 2/3 Memory Pwr Cntrl RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
發布緊急采購，3分鐘左右您將得到回復。