- 您現在的位置：買賣IC網 > PDF目錄69048 > PKB4711PINBM (ERICSSON POWER MODULES AB) 1-OUTPUT 75 W DC-DC REG PWR SUPPLY MODULE PDF資料下載
參數資料
| 型號： | PKB4711PINBM |
| 廠商： | ERICSSON POWER MODULES AB |
| 元件分類： | 電源模塊 |
| 英文描述： | 1-OUTPUT 75 W DC-DC REG PWR SUPPLY MODULE |
| 封裝： | ROHS COMPLIANT, EIGHTH BRICK PACKAGE-8 |
| 文件頁數： | 35/46頁 |
| 文件大小： | 1643K |
| 代理商： | PKB4711PINBM |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁當前第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁
Ericsson Internal
PRODUCT SPECIFICATION
3 (5)
Prepared (also subject responsible if other)
No.
EJUNGYA
3/1301-BMR 636 Uen
Approved
Checked
Date
Rev
Reference
SEC/D (Julia You)
ESHUHAN
2008-1-11
A
Operating information continued
Parallel Operation
Two converters may be paralleled for redundancy if the total
power is equal or less than PO max. It is not recommended to
parallel the converters without using external current sharing
circuits.
See Design Note 006 for detailed information.
Remote Sense
The DC/DC converters have remote sense that can be used
to compensate for voltage drops between the output and the
point of load. The sense traces should be located close to the
PCB ground layer to reduce noise susceptibility. The remote
sense circuitry will compensate for up to 10% voltage drop
between output pins and the point of load.
If the remote sense is not needed +Sense should be
connected to +Out and -Sense should be connected to -Out.
Over Temperature Protection (OTP)
The converters are protected from thermal overload by the
control IC.
When Tref as defined in thermal consideration section
exceeds 135°C the converter will shut down. The DC/DC
converter will make continuous attempts to start up (non-
latching mode) and resume normal operation automatically
when the temperature has dropped >10°C below the
temperature threshold.
Over Voltage Protection (OVP)
The converters have output over voltage protection that will
shut down the converter in over voltage conditions. The
converter will make continuous attempts to start up (non-
latching mode) and resume normal operation automatically
after removal of the over voltage condition.
Over Current Protection (OCP)
The converters include current limiting circuitry for protection
at continuous overload.
The output voltage will decrease towards zero for output
currents in excess of max output current (max IO). The
converter will resume normal operation after removal of the
overload. The load distribution should be designed for the
maximum output short circuit current specified.
Thermal Consideration
General
The converters are designed to operate in different thermal
environments and sufficient cooling must be provided to
ensure reliable operation.
Cooling is achieved mainly by conduction, from the pins to
the host board, and convection, which is dependant on the
airflow across the converter. Increased airflow enhances the
cooling of the converter.
The Output Current Derating graph found in the Output
section for each model provides the available output current
vs. ambient air temperature and air velocity at Vin = 53 V.
The DC/DC converter is tested on a 254 x 254 mm,
35 m (1 oz), 8-layer test board mounted vertically in a wind
tunnel with a cross-section of 305 x 305 mm.
Proper cooling of the DC/DC converter can be verified by
measuring the temperature at positions P1, P2 and P3. The
temperature at these positions should not exceed the max
values provided in the table below.
Note that the max value is the absolute maximum rating
(non destruction) and that the electrical Output data is
guaranteed up to Tref +90°C.
See Design Note 019 for further information.
Position
Device
Designation
max value
P1
Pcb
110 C
P2
Mosfet
120 C
P3
Mosfet
Tref
120 C
E
PKB 4000 series
DC/DC converters, Input 36-75 V, Output 30 A/90 W
EN/LZT 146 394 R5A August 2009
Ericsson AB
Technical Specication
40
相關PDF資料 |
PDF描述 |
|---|---|
| PKB4711PINBLA | 1-OUTPUT 75 W DC-DC REG PWR SUPPLY MODULE |
| PKB4711PINBLB | 1-OUTPUT 75 W DC-DC REG PWR SUPPLY MODULE |
| PKB4711PINB | 1-OUTPUT 75 W DC-DC REG PWR SUPPLY MODULE |
| PKB4718CPILPA | 1-OUTPUT 72 W DC-DC REG PWR SUPPLY MODULE |
| PKB4718CPILV | 1-OUTPUT 72 W DC-DC REG PWR SUPPLY MODULE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PKB4711PINBMLA | 制造商:Ericsson 功能描述:DC/DC PS SGL-OUT 5V 15A 75W - Bulk |
| PKB4711PINBMLA REV.R2A | 制造商:Ericsson 功能描述:PKB 1/8TH-BRICK SERIES, ISOLATED, CONVERTER - Bulk |
| PKB4711PIPNB | 制造商:Ericsson 功能描述:- Trays 制造商:Ericsson 功能描述:Ericsson PKB4711PIPNB DC to DC |
| PKB4711PIPNBLA | 制造商:Ericsson 功能描述:- Trays |
| PKB4711SINB | 功能描述:DC/DC轉換器 75W 36-75Vin 5V 15A SMT RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
發布緊急采購，3分鐘左右您將得到回復。