- 您現在的位置：買賣IC網 > PDF目錄69048 > PKB4418PINBLB (ERICSSON POWER MODULES AB) 1-OUTPUT 45 W DC-DC REG PWR SUPPLY MODULE PDF資料下載
參數資料
| 型號： | PKB4418PINBLB |
| 廠商： | ERICSSON POWER MODULES AB |
| 元件分類： | 電源模塊 |
| 英文描述： | 1-OUTPUT 45 W DC-DC REG PWR SUPPLY MODULE |
| 封裝： | ROHS COMPLIANT, PACKAGE-8 |
| 文件頁數： | 36/43頁 |
| 文件大小： | 1656K |
| 代理商： | PKB4418PINBLB |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁當前第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁
Ericsson Internal
PROD. SPECIFICATION MECHANICAL
1 (4)
Prepared (also subject responsible if other)
No.
EPANHON
5/1301-BMR 636 Uen
Approved
Checked
Date
Rev
Reference
SEC/D [Julia You]
See §1
2007-10-15
B
Soldering Information - Surface Mounting
The surface mount version of the product is intended for
convection or vapor phase reflow SnPb and Pb-free
processes. To achieve a good and reliable soldering result,
make sure to follow the recommendations from the solder
paste supplier, to use state-of-the-art reflow equipment and
reflow profiling techniques as well as the following guidelines.
A no-clean flux is recommended to avoid entrapment of
cleaning fluids in cavities inside the product or between the
product and the host board. The cleaning residues may affect
long time reliability and isolation voltage.
Minimum Pin Temperature Recommendations
Pin number 4 is chosen as reference location for the minimum
pin temperature recommendations since this will likely be the
coolest solder joint during the reflow process.
Pin 4 for measurement of minimum
solder joint temperature, TPIN
Pin 2 for measurement of maximum
peak product reflow temperature, TP
SnPb solder processes
For SnPb solder processes, a pin temperature (T
PIN) in excess
of the solder melting temperature, (T
L, +183°C for Sn63/Pb37)
for more than 30 seconds, and a peak temperature of +210°C
is recommended to ensure a reliable solder joint.
Lead-free (Pb-free) solder processes
For Pb-free solder processes, a pin temperature (T
PIN) in
excess of the solder melting temperature (T
L, +217 to +221°C
for Sn/Ag/Cu solder alloys) for more than 30 seconds, and a
peak temperature of +235°C on all solder joints is
recommended to ensure a reliable solder joint.
Peak Product Temperature Requirements
Pin number 2 is chosen as reference location for the
maximum (peak) allowed product temperature (T
P) since this
will likely be the warmest part of the product during the reflow
process.
To avoid damage or performance degradation of the product,
the reflow profile should be optimized to avoid excessive
heating. A sufficiently extended preheat time is recommended
to ensure an even temperature across the host PCB, for both
small and large devices. To reduce the risk of excessive
heating is also recommended to reduce the time in the reflow
zone as much as possible.
SnPb solder processes
For SnPb solder processes, the product is qualified for MSL 1
according to IPC/JEDEC standard J-STD-020C.
During reflow, T
P must not exceed +225°C at any time.
Lead-free (Pb-free) solder processes
For Pb-free solder processes, the product is qualified for
MSL 3 according to IPC/JEDEC standard J-STD-020C.
During reflow, T
P must not exceed +260°C at any time.
25 °C
Time
Temperature
Ramp-down
(cooling)
Ramp-up
Reflow
Preheat
Time 25 °C to peak
T
P
T
L
Reflow process specifications
Sn/Pb eutectic
Pb-free
Average ramp-up rate
3°C/s max
Solder melting
temperature (typical)
T
L
+183°C
+221°C
Minimum time above T
L
30 s
Minimum pin temperature
T
PIN
+210°C
+235°C
Peak product temperature T
P
+225°C
+260°C
Average ramp-down rate
6°C/s max
Time 25°C to peak
6 minutes max
8 minutes max
E
PKB 4000 series
DC/DC converters, Input 36-75 V, Output 30 A/90 W
EN/LZT 146 394 R4A Sep 2008
Ericsson Power Modules AB
Technical Specication
41
相關PDF資料 |
PDF描述 |
|---|---|
| PKB4913PINBLB | 1-OUTPUT 90 W DC-DC REG PWR SUPPLY MODULE |
| PKB4715PINBLB | 1-OUTPUT 75 W DC-DC REG PWR SUPPLY MODULE |
| PKB4619PINBLB | 1-OUTPUT 62.5 W DC-DC REG PWR SUPPLY MODULE |
| PKB4418PIPNB | 1-OUTPUT 45 W DC-DC REG PWR SUPPLY MODULE |
| PKB4610PINBLB | 1-OUTPUT 66 W DC-DC REG PWR SUPPLY MODULE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PKB4418PIOANB | 功能描述:DC/DC轉換器 1.5 Vdc 30A Iso Input 36-75V 45W RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
| PKB4418PIOANBLA | 制造商:Ericsson 功能描述:MOD,DC/DC 48V IN/1.5V OUT,25A,ISO,EBRICK - Bulk |
| PKB4418PIOANBLB | 制造商:Ericsson 功能描述:MOD,DC/DC 48V IN/1.5V OUT,25A,ISO,EBRICK - Bulk 制造商:Ericsson 功能描述:Ericsson PKB4418PIOANBLB DC to DC |
| PKB4418SIOANB | 制造商:Ericsson 功能描述:- Trays |
| PKB4513PINBLC | 功能描述:DC/DC 開關控制器 DC/DC CONV in 36-60V output 12V 4A 48W RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
發布緊急采購，3分鐘左右您將得到回復。