- 您現在的位置：買賣IC網 > PDF目錄69045 > PKB4118GCPI (ERICSSON POWER MODULES AB) 1-OUTPUT 108 W DC-DC REG PWR SUPPLY MODULE PDF資料下載
參數資料
| 型號： | PKB4118GCPI |
| 廠商： | ERICSSON POWER MODULES AB |
| 元件分類： | 電源模塊 |
| 英文描述： | 1-OUTPUT 108 W DC-DC REG PWR SUPPLY MODULE |
| 封裝： | ROHS COMPLIANT, EIGHTH-BRICK PACKAGE-8 |
| 文件頁數： | 31/39頁 |
| 文件大?。?/td> | 1773K |
| 代理商： | PKB4118GCPI |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁當前第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁
Ericsson Internal
PROD. SPECIFICATION MECHANICAL
1 (4)
Prepared (also subject responsible if other)
No.
MICJAN
5/1301-BMR 655 Uen
Approved
Checked
Date
Rev
Reference
MPM/BK/P [Natalie Johansson]
See §1
2007-05-29
B
Soldering Information - Surface Mounting
The surface mount version of the product is intended for
convection or vapor phase reflow SnPb and Pb-free
processes. To achieve a good and reliable soldering result,
make sure to follow the recommendations from the solder
paste supplier, to use state-of-the-art reflow equipment and
reflow profiling techniques as well as the following guidelines.
A no-clean flux is recommended to avoid entrapment of
cleaning fluids in cavities inside the product or between the
product and the host board. The cleaning residues may affect
long time reliability and isolation voltage.
Minimum Pin Temperature Recommendations
Pin number 4 is chosen as reference location for the minimum
pin temperature recommendations since this will likely be the
coolest solder joint during the reflow process.
Pin 4 for measurement of minimum
solder joint temperature, TPIN
Pin 2 for measurement of maximum
peak product reflow temperature, TP
SnPb solder processes
For SnPb solder processes, a pin temperature (T
PIN) in excess
of the solder melting temperature, (T
L, +183°C for Sn63/Pb37)
for more than 30 seconds, and a peak temperature of +210°C
is recommended to ensure a reliable solder joint.
Lead-free (Pb-free) solder processes
For Pb-free solder processes, a pin temperature (T
PIN) in
excess of the solder melting temperature (T
L, +217 to +221°C
for Sn/Ag/Cu solder alloys) for more than 30 seconds, and a
peak temperature of +235°C on all solder joints is
recommended to ensure a reliable solder joint.
Peak Product Temperature Requirements
Pin number 2 is chosen as reference location for the
maximum (peak) allowed product temperature (T
P) since this
will likely be the warmest part of the product during the reflow
process.
To avoid damage or performance degradation of the product,
the reflow profile should be optimized to avoid excessive
heating. A sufficiently extended preheat time is recommended
to ensure an even temperature across the host PCB, for both
small and large devices. To reduce the risk of excessive
heating is also recommended to reduce the time in the reflow
zone as much as possible.
SnPb solder processes
For SnPb solder processes, the product is qualified for MSL 1
according to IPC/JEDEC standard J-STD-020C.
During reflow, T
P must not exceed +225°C at any time.
Lead-free (Pb-free) solder processes
For Pb-free solder processes, the product is qualified for
MSL 3 according to IPC/JEDEC standard J-STD-020C.
During reflow, T
P must not exceed +260°C at any time.
25 °C
Time
Temperature
Ramp-down
(cooling)
Ramp-up
Reflow
Preheat
Time 25 °C to peak
T
P
T
L
Reflow process specifications
Sn/Pb eutectic
Pb-free
Average ramp-up rate
3°C/s max
Solder melting
temperature (typical)
T
L
+183°C
+221°C
Minimum time above T
L
30 s
Minimum pin temperature
T
PIN
+210°C
+235°C
Peak product temperature T
P
+225°C
+260°C
Average ramp-down rate
6°C/s max
Time 25°C to peak
6 minutes max
8 minutes max
E
PKB4000C PI
DC/DC converters, Input 36-75 V, Output 60A/144W
EN/LZT 146 377 R3G
Oct 2008
Ericsson Power Modules AB
Technical Specification
37
相關PDF資料 |
PDF描述 |
|---|---|
| PKB4918HCPI | DC-DC REG PWR SUPPLY MODULE |
| PKB4110CPI | 1-OUTPUT 132 W DC-DC REG PWR SUPPLY MODULE |
| PKB4718LCPI | 1-OUTPUT 72 W DC-DC REG PWR SUPPLY MODULE |
| PKB4201BPIPHSMLA/B | 1-OUTPUT 204 W DC-DC REG PWR SUPPLY MODULE |
| PKB4207LBSIHSM/B | 1-OUTPUT 264 W DC-DC REG PWR SUPPLY MODULE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PKB4118HCPI | 功能描述:DC/DC轉換器 1.5Vdc 50A Isolated Input 36-75V 75W RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
| PKB4201BPI | 功能描述:DC/DC轉換器 200W 36-75Vin, 40A RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
| PKB4204BPI | 功能描述:DC/DC轉換器 240W 36-75Vin/12Vout 1/8-BRICK RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
| PKB4204BPILB | 制造商:Ericsson 功能描述:POWER CONVERTER, NON-ISOLATED DC-DC |
| PKB4204PI | 功能描述:DC/DC轉換器 240W 12V 20A 40-75Vin RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
發布緊急采購，3分鐘左右您將得到回復。