- 您現在的位置：買賣IC網 > PDF目錄368030 > PIP201-12M-3 (NXP SEMICONDUCTORS) DC-to-DC converter powertrain PDF資料下載
參數資料
| 型號： | PIP201-12M-3 |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 穩壓器 |
| 英文描述： | DC-to-DC converter powertrain |
| 中文描述： | 200 A SWITCHING REGULATOR, PQCC68 |
| 封裝： | 10 X 10 MM, 0.85 MM HEIGHT, PLASTIC, SOT-687-1, HVQFN-68 |
| 文件頁數： | 15/20頁 |
| 文件大小： | 345K |
| 代理商： | PIP201-12M-3 |
Philips Semiconductors
PIP201-12M-3
DC-to-DC converter powertrain
Product data
Rev. 03 — 19 November 2003
15 of 20
9397 750 11942
Koninklijke Philips Electronics N.V. 2003. All rights reserved.
15. Soldering
15.1 Introduction to soldering MLF packages
The MicroLeadFrame package (MLF) is a near Chip Scale Package (CSP) with a
copper leadframe. It is a leadless package, where electrical contact to the printed
circuit board is made through metal pads on the underside of the package. In addition
to the small pads around the periphery of the package, there are large pads on the
underside that provide low thermal resistance, low electrical resistance, low
inductance connections between the power components inside the MLF package and
the printed-circuit board. It is this feature of the MLF package that makes it ideally
suited for VRM applications.
Electrical connection between the package and the printed circuit board is made by
printing solder paste on the printed circuit board, placing the component and
reflowing the solder in a convection or infra-red oven. The solder reflow process is
shown in
Figure 18
and the typical temperature profile is shown in
Figure 19
. To
ensure good solder joints, the peak temperature T
p
should not exceed 220
°
C for thin
packages such as MLF, and the time above liquidus temperature should be less than
1.25 minutes. The maximum temperature can be increased for lead free solder. The
ramp rate during preheat should not exceed 3 K/s. Nitrogen purge is recommended
during reflow.
Fig 18. Typical reflow soldering process flow.
Fig 19. Typical reflow soldering temperature profile.
SOLDER PASTE
PRINTING
POST PRINT
INSPECTION
COMPONENT
PLACEMENT
PRE REFLOW
INSPECTION
REFLOW SOLDERING
POST REFLOW INSPECTION
(PREFERABLY X-RAY)
REWORK AND
TOUCH UP
03aj25
03aj26
0
100
200
300
0
1
2
3
time (minutes)
Temp
(
°
C)
Tr
Te
Tp
rate of rise of
temperature < 3 K/s
1 min max
1.25 min max
相關PDF資料 |
PDF描述 |
|---|---|
| PIP3102-R | LOGIC LEVEL TOPFET |
| PIP3203-A | TOPFET high side switch |
| PIP3206-R | TOPFET high side switch SMD version |
| PIP8.4 | 7,500 & 15,000 Watt TVS Module |
| PIP208 | 15,000 Watt TVS Module(15，000W,鉗位電壓536V，瞬變電壓抑制器模塊) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PIP201-12M-3,518 | 功能描述:IC REG BUCK SYNC ADJ 20A 68HVQFN RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:20 系列:SIMPLE SWITCHER® 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:12V 輸入電壓:4 V ~ 60 V PWM 型:電壓模式 頻率 - 開關:52kHz 電流 - 輸出:1A 同步整流器:無 工作溫度:-40°C ~ 125°C 安裝類型:通孔 封裝/外殼:16-DIP（0.300"，7.62mm） 包裝:管件 供應商設備封裝:16-DIP 其它名稱:*LM2575HVN-12LM2575HVN-12 |
| PIP202-12M | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:DC to DC converter powertrain |
| PIP202-12M-2 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:DC-to-DC converter powertrain |
| PIP202-12M-2 /T3 | 功能描述:直流/直流開關轉換器 TAPE7 MOSFET RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| PIP202-12M-2,518 | 功能描述:直流/直流開關調節器 TAPE7 MOSFET RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5 |
發布緊急采購，3分鐘左右您將得到回復。