- 您現在的位置：買賣IC網 > PDF目錄98052 > PIM200FZ (LINEAGE POWER LLC) 1-OUTPUT 7.92 W DC-DC REG PWR SUPPLY MODULE PDF資料下載
參數資料
| 型號： | PIM200FZ |
| 廠商： | LINEAGE POWER LLC |
| 元件分類： | 電源模塊 |
| 英文描述： | 1-OUTPUT 7.92 W DC-DC REG PWR SUPPLY MODULE |
| 封裝： | ROHS COMPLIANT PACKAGE-13 |
| 文件頁數： | 4/18頁 |
| 文件大?。?/td> | 346K |
| 代理商： | PIM200FZ |
Data Sheet
October 5, 2009
PIM200X Series; ATCA Board Power Input Modules
-38 to -75Vdc; 200W Input
LINEAGE POWER
12
C22.2 No. 60950-1-03, and VDE 0850:2001-12
(EN60950-1) Licensed.
The power input to these units is to be provided with a
maximum of 10 Amps fuses with a voltage rating of at
least 75Vdc.
Refer to “Thermal Considerations” section for
additional safety considerations.
Feature Description
A/B Feed OR’ing
The module provides dedicated OR’ing functionality
to both Feeds A & B and their corresponding returns.
The following pairs of signals are OR’d within the
module:
-48V_AF / -48_BF, VRTN_AF / VRTN_BF, and
ENABLE_AF/ ENABLE_B.
The -48V A/B feeds and their corresponding returns
are OR’d via N-channel MOSFET power devices
resulting in a highly efficient system compared to
conventional diode OR’ing scheme.
EMC Filtering
The module incorporates an EMI filter that is designed
for the ATCA board to help meet the conducted
emissions requirements of CISPR 22 Class B when
used in conjunction with Lineage Power DC/DC
converters approved for ATCA applications. The
following insertion loss table is provided as filter
performance guidelines.
Parameter
Typical
Unit
Common-Mode Insertion Loss
50 Ohms circuit, 200kHz
25
dB
50 Ohms circuit, 500kHz
30
dB
50 Ohms circuit, 1MHz
40
dB
Differential-mode Insertion Loss
50 Ohms circuit, 200kHz
80
dB
50 Ohms circuit, 500kHz
70
dB
50 Ohms circuit, 1MHz
60
dB
The following Figure 13 depicts the Class B EMI
performance of PIM200F when tested with
QBW018A0B1 on a stand alone basis (ATCA form
factor load board with resistive loads and only power,
return and chassis connections to the backplane).
The external filtering components are identified in the
Typical Application circuit.
Figure 13. Typical Class B EMC signature of
PIM200F with QBW018A0B1 module.
For Safety and noise considerations, copper traces
must not be routed directly beneath the power module
(PWB top layer). C_EMI capacitors must make direct
connections (preferably without vias) to the DC/DC
module pins with as much copper width as possible.
In case vias are necessary, allow for multiple
connections to the inner plane with vias placed
outside the footprint of the module. For additional
layout guide-lines, refer to Lineage Power’s’s
FLT007A0 Input Filter Module data sheet.
Inrush Current Control / Hot Plug
Functionality
The module provides inrush current control / hot plug
capability. The peak value of the inrush current and
the duration complies with the PICMG 3.0’s Inrush
Transient specifications. The specifications shall be
met with the external C_HLDP and C_FLTR
capacitances as specified in the previous sections.
The unique design of the module where the large
energy storage capacitors are segregated from the
input filter capacitors allows the module to meet the
stringent PICMG’s inrush transient specifications. In
conventional designs where the energy storage
capacitors and the filter capacitors are in parallel, it is
extremely difficult to meet the inrush transient
specifications without over sizing the inrush control
power FET.
A/B Feed / Fuse Alarm (-48V_ALARM)
The module monitors the A & B feeds as well as the
status of the A&B feed fuses and provides an opto-
isolated signal in case of loss of a feed or the opening
of any of the fuses. The response time of the fault
condition is < 100 μsec. The alarm signal indicates
normal operation when the optocoupler transistor is
conducting and a fault condition by an off state.
相關PDF資料 |
PDF描述 |
|---|---|
| PIM300FZ | 2-OUTPUT 7.9 W DC-DC REG PWR SUPPLY MODULE |
| PIM300F6Z | 2-OUTPUT 7.9 W DC-DC REG PWR SUPPLY MODULE |
| PIP201-12M-3,518 | 200 A SWITCHING REGULATOR, PQCC68 |
| PIP201-12M | SPECIALTY ANALOG CIRCUIT, PQCC68 |
| PIP8000FHN/N1 | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC28 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PIM213 | 功能描述:AUTOMATION HAT (INDIVIDUAL) 制造商:pimoroni ltd 系列:- 零件狀態:在售 平臺:Raspberry Pi 類型:接口 功能:自動化 使用的 IC/零件:- 內容:板 標準包裝:1 |
| PIM215 | 功能描述:PICADE HAT (HAT ONLY) 制造商:pimoroni ltd 系列:- 零件狀態:在售 平臺:Raspberry Pi 類型:接口 功能:弓形板 使用的 IC/零件:- 內容:板 標準包裝:1 |
| PIM216 | 功能描述:MOTE PHAT 制造商:pimoroni ltd 系列:- 零件狀態:在售 平臺:Raspberry Pi 類型:電源管理 功能:LED 驅動器 使用的 IC/零件:- 內容:板 標準包裝:1 |
| PIM221 | 功能描述:AUTOMATION PHAT 制造商:pimoroni ltd 系列:- 零件狀態:在售 平臺:Raspberry Pi 類型:接口 功能:自動化 使用的 IC/零件:- 內容:板 標準包裝:1 |
| PIM242 | 功能描述:RAINBOW HAT (RAINBOW HAT ONLY) 制造商:pimoroni ltd 系列:- 零件狀態:在售 平臺:Raspberry Pi 類型:接口 功能:多重 使用的 IC/零件:- 內容:板 標準包裝:1 |
發布緊急采購，3分鐘左右您將得到回復。