- 您現在的位置：買賣IC網 > PDF目錄1965 > PIC18LF8722-I/PT (Microchip Technology)IC PIC MCU FLASH 64KX16 80TQFP PDF資料下載
參數資料
| 型號： | PIC18LF8722-I/PT |
| 廠商： | Microchip Technology |
| 文件頁數： | 3/16頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC PIC MCU FLASH 64KX16 80TQFP |
| 產品培訓模塊： | Asynchronous Stimulus 8-bit PIC® Microcontroller Portfolio |
| 標準包裝： | 119 |
| 系列： | PIC® 18F |
| 核心處理器： | PIC |
| 芯體尺寸： | 8-位 |
| 速度： | 40MHz |
| 連通性： | EBI/EMI，I²C，SPI，UART/USART |
| 外圍設備： | 欠壓檢測/復位，HLVD，POR，PWM，WDT |
| 輸入/輸出數： | 70 |
| 程序存儲器容量： | 128KB（64K x 16） |
| 程序存儲器類型： | 閃存 |
| EEPROM 大?。?/td> | 1K x 8 |
| RAM 容量： | 3.8K x 8 |
| 電壓 - 電源 (Vcc/Vdd)： | 2 V ~ 5.5 V |
| 數據轉換器： | A/D 16x10b |
| 振蕩器型： | 內部 |
| 工作溫度： | -40°C ~ 85°C |
| 封裝/外殼： | 80-TQFP |
| 包裝： | 托盤 |
| 產品目錄頁面： | 644 (CN2011-ZH PDF) |
2006 Microchip Technology Inc.
DS80221C-page 11
PIC18F6627/6722/8627/8722
32. Module: MSSP (I2C Mode)
It has been observed that, following a Power-on
Reset, I2C mode may not initialize properly by just
configuring the SCLx and SDAx pins as either
inputs or outputs. This has only been seen in a few
unique system environments.
A test of a statistically significant sample of pre-
production systems, across the voltage and
current range of the application's power supply,
should indicate if a system is susceptible to this
issue.
Work around
Before configuring the module for I2C operation:
1. Configure the SCLx and SDAx pins as outputs
by clearing their corresponding TRIS bits.
2. Force SCLx and SDAx low by clearing the
corresponding LAT bits.
3. While keeping the LAT bits clear, configure
SCLx and SDAx as inputs by setting their TRIS
bits.
Once this is done, use the SSPxCON1 and
SSPxCON2 registers to configure the proper I2C
mode as before.
Date Codes that pertain to this issue:
All engineering and production devices.
33. Module: MSSP (I2C Mode)
In I2C Master mode, the RCEN bit is set by soft-
ware to begin data reception, and cleared by the
peripheral after a byte is received. After a byte is
received, the device may take up to 80 TCY to clear
RCEN and 800 TCY during emulation.
Work around
Single byte receptions are typically not affected,
since the delay between byte receptions typically
is long enough for the RCEN bit to clear. For mul-
tiple byte receptions, the software must wait until
the bit is cleared by the peripheral before the next
byte can be received.
Date Codes that pertain to this issue:
All engineering and production devices.
34. Module: ECCP (PWM Mode)
When
the
PWM
auto-shutdown
feature
is
configured for automatic restart by setting the
PxRSEN bit (ECCPxDEL<7>), the pulse may
terminate immediately in a shutdown event. In
addition, the pulse may restart within the period if
the shutdown condition expires. This may result in
the generation of short pulses on the PWM
output(s).
Work around
Configure the auto-shutdown for software restart
by clearing the PxRSEN bit. The PWM can be re-
enabled
by
clearing
the
ECCPxASE
bit
(ECCPxAS<7>) after the shutdown condition
expires.
Date Codes that pertain to this issue:
All engineering and production devices.
35. Module: ECCP (PWM Mode)
When configured for half-bridge operation with
dead band (CCPxCON<7:6> = 10), the PWM out-
put may be corrupted for certain values of the
PWM duty cycle. This can occur when these
additional criteria are also met:
a non-zero, dead-band delay is specified
(PxDC6:PxDC0 > 0); and
the duty cycle has a value of 0 through 3, or
4n + 3 (n
≥ 1).
Work around
None.
Date Codes that pertain to this issue:
All engineering and production devices.
36. Module: CCP (PWM Mode)
Timer4 is not available as a clock source for either
CCP4
or
CCP5
in
any
PWM
mode
(CCPxCON<3:2> = 11). Selecting Timer4 as the
module’s clock source may cause the PWM output
to stop generating pulses.
Work around
To use CCP4 or CCP5 in PWM mode, use only
Timer2 as the clock source (T3CON<6,3> = 00).
Date Codes that pertain to this issue:
All engineering and production devices.
相關PDF資料 |
PDF描述 |
|---|---|
| PIC18LF96J65-I/PT | IC PIC MCU FLASH 48KX16 100TQFP |
| PIC24F16KL401-I/P | IC MCU 16BIT 16KB FLASH 20-PDIP |
| PIC24FJ128GA010-I/PF | IC PIC MCU FLASH 128KB 100TQFP |
| PIC24FJ256GA110-I/PF | IC PIC MCU FLASH 256K 100TQFP |
| PIC24FJ256GB110-I/PF | IC PIC MCU FLASH 256K 100TQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PIC18LF8722T-I/PT | 功能描述:8位微控制器 -MCU 128 KB FL 4K RAM 70 I/O RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| PIC18LF8723-I/PT | 功能描述:8位微控制器 -MCU 128KB Flash 4KB RAM 1024 DataEE 12B ADC RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| PIC18LF8723T-I/PT | 功能描述:8位微控制器 -MCU 128KB Flash 4KB RAM 1024 DataEE 12B ADC RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| PIC18LF96J65-I/PT | 功能描述:IC PIC MCU FLASH 48KX16 100TQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:PIC® 18F 產品培訓模塊:XLP Deep Sleep Mode 8-bit PIC® Microcontroller Portfolio 標準包裝:22 系列:PIC® XLP™ 18F 核心處理器:PIC 芯體尺寸:8-位 速度:48MHz 連通性:I²C，SPI，UART/USART，USB 外圍設備:欠壓檢測/復位，POR，PWM，WDT 輸入/輸出數:14 程序存儲器容量:8KB（4K x 16） 程序存儲器類型:閃存 EEPROM 大小:256 x 8 RAM 容量:512 x 8 電壓 - 電源 (Vcc/Vdd):1.8 V ~ 5.5 V 數據轉換器:A/D 11x10b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:20-DIP（0.300"，7.62mm） 包裝:管件 產品目錄頁面:642 (CN2011-ZH PDF) 配用:DV164126-ND - KIT DEVELOPMENT USB W/PICKIT 2DM164127-ND - KIT DEVELOPMENT USB 18F14/13K50AC164112-ND - VOLTAGE LIMITER MPLAB ICD2 VPP |
| PIC1-R68-JT | 制造商:RCD 制造商全稱:RCD COMPONENTS INC. 功能描述:SURFACE MOUNT POWER INDUCTORS |
發布緊急采購，3分鐘左右您將得到回復。