- 您現在的位置：買賣IC網 > PDF目錄368027 > PIC18F458TIPQTP (Microchip Technology Inc.) High Performance, 28/40-Pin Enhanced FLASH Microcontrollers with CAN PDF資料下載
參數資料
| 型號： | PIC18F458TIPQTP |
| 廠商： | Microchip Technology Inc. |
| 英文描述： | High Performance, 28/40-Pin Enhanced FLASH Microcontrollers with CAN |
| 中文描述： | 高性能，28/40-Pin增強型閃存微控制器和CAN |
| 文件頁數： | 168/384頁 |
| 文件大小： | 3119K |
| 代理商： | PIC18F458TIPQTP |
PIC18FXX8
DS41159B-page 166
Preliminary
2002 Microchip Technology Inc.
17.4.6.1
I
2
C Master Mode Operation
The master device generates all of the serial clock
pulses and the START and STOP conditions. A trans-
fer is ended with a STOP condition or with a Repeated
START condition. Since the Repeated START condi-
tion is also the beginning of the next serial transfer, the
I
2
C bus will not be released.
In Master Transmitter mode, serial data is output
through SDA, while SCL outputs the serial clock. The
first byte transmitted contains the slave address of the
receiving device (7 bits) and the Read/Write (R/W) bit.
In this case, the R/W bit will be logic ’0’. Serial data is
transmitted 8 bits at a time. After each byte is transmit-
ted, an Acknowledge bit is received. START and STOP
conditions are output to indicate the beginning and the
end of a serial transfer.
In Master Receive mode, the first byte transmitted con-
tains the slave address of the transmitting device
(7 bits) and the R/W bit. In this case, the R/W bit will be
logic ’1’. Thus, the first byte transmitted is a 7-bit slave
address followed by a ’1’ to indicate receive bit. Serial
data is received via SDA, while SCL outputs the serial
clock. Serial data is received 8 bits at a time. After each
byte is received, an Acknowledge bit is transmitted.
START and STOP conditions indicate the beginning
and end of transmission.
The baud rate generator used for the SPI mode opera-
tion is used to set the SCL clock frequency for either
100 kHz, 400 kHz or 1 MHz I
2
C operation. See
Section 17.4.7, Baud Rate Generator for more details.
A typical transmit sequence would go as follows:
1.
The user generates a START condition by set-
ting
the
START
(SSPCON2<0>).
2.
SSPIF is set. The MSSP module will wait the
required start time before any other operation
takes place.
3.
The user loads the SSPBUF with the slave
address to transmit.
4.
Address is shifted out the SDA pin until all 8 bits
are transmitted.
5.
The MSSP module shifts in the ACK bit from the
slave device and writes its value into the
SSPCON2 register (SSPCON2<6>).
6.
The MSSP module generates an interrupt at the
end of the ninth clock cycle by setting the SSPIF
bit.
7.
The user loads the SSPBUF with eight bits of
data.
8.
Data is shifted out the SDA pin until all 8 bits are
transmitted.
9.
The MSSP Module shifts in the ACK bit from the
slave device and writes its value into the
SSPCON2 register (SSPCON2<6>).
10. The MSSP module generates an interrupt at the
end of the ninth clock cycle by setting the SSPIF
bit.
11. The user generates a STOP condition by setting
the STOP enable bit PEN (SSPCON2<2>).
12. Interrupt is generated once the STOP condition
is complete.
enable
bit,
SEN
相關PDF資料 |
PDF描述 |
|---|---|
| PIC18F458TIPSQTP | High Performance, 28/40-Pin Enhanced FLASH Microcontrollers with CAN |
| PIC18F458TIPTQTP | High Performance, 28/40-Pin Enhanced FLASH Microcontrollers with CAN |
| PIC18F458TIPTSQTP | High Performance, 28/40-Pin Enhanced FLASH Microcontrollers with CAN |
| PIC18F458TISOQTP | High Performance, 28/40-Pin Enhanced FLASH Microcontrollers with CAN |
| PIC18F458TISOSQTP | High Performance, 28/40-Pin Enhanced FLASH Microcontrollers with CAN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PIC18F45J10-E/ML | 功能描述:8位微控制器 -MCU 32 KB Flash 1 KB RAM RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| PIC18F45J10-E/P | 功能描述:8位微控制器 -MCU 32 KB Flash 1 KB RAM RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| PIC18F45J10-E/PT | 功能描述:8位微控制器 -MCU 32 KB Flash 1 KB RAM RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| PIC18F45J10-I/ML | 功能描述:8位微控制器 -MCU 32 KB FL 1024 RAM RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| PIC18F45J10-I/P | 功能描述:8位微控制器 -MCU 32 KB FL 1 KB RAM RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。