參數資料
型號： PIC18F4321-I/ML
廠商： Microchip Technology
文件頁數： 31/110頁
文件大?。?/td> 0K
描述： IC PIC MCU FLASH 4KX16 44QFN
產品培訓模塊： Asynchronous Stimulus
8-bit PIC® Microcontroller Portfolio
標準包裝： 45
系列： PIC® 18F
核心處理器： PIC
芯體尺寸： 8-位
速度： 40MHz
連通性： I²C，SPI，UART/USART
外圍設備： 欠壓檢測/復位，HLVD，POR，PWM，WDT
輸入/輸出數： 36
程序存儲器容量： 8KB（4K x 16）
程序存儲器類型： 閃存
EEPROM 大小： 256 x 8
RAM 容量： 512 x 8
電壓 - 電源 (Vcc/Vdd)： 4.2 V ~ 5.5 V
數據轉換器： A/D 13x10b
振蕩器型： 內部
工作溫度： -40°C ~ 85°C
封裝/外殼： 44-VQFN 裸露焊盤
包裝： 管件
產品目錄頁面： 642 (CN2011-ZH PDF)
配用： XLT44QFN2-ND - SOCKET TRAN ICE 44QFN/40DIP
AC164322-ND - MODULE SOCKET MPLAB PM3 28/44QFN
444-1001-ND - DEMO BOARD FOR PICMICRO MCU
2009 Microchip Technology Inc.
DS39689F-page 27
PIC18F2221/2321/4221/4321 FAMILY
2.4
ICSP Pins
The PGC and PGD pins are used for In-Circuit Serial
Programming (ICSP) and debugging purposes. It is
recommended to keep the trace length between the
ICSP connector and the ICSP pins on the device as
short as possible. If the ICSP connector is expected to
experience an ESD event, a series resistor is recom-
mended, with the value in the range of a few tens of
ohms, not to exceed 100.
Pull-up resistors, series diodes and capacitors on the
PGC and PGD pins are not recommended as they will
interfere
with
the
programmer/debugger
com-
munications to the device. If such discrete components
are an application requirement, they should be removed
from the circuit during programming and debugging.
Alternatively, refer to the AC/DC characteristics and
timing requirements information in the respective device
Flash programming specification for information on
capacitive loading limits and pin input voltage high (VIH)
and input low (VIL) requirements.
For device emulation, ensure that the “Communication
Channel Select” (i.e., PGC/PGD pins) programmed
into the device matches the physical connections for
the ICSP to the MPLAB ICD 2, MPLAB ICD 3 or REAL
ICE emulator.
For more information on the ICD 2, ICD 3 and REAL
ICE emulator connection requirements, refer to the
following documents that are available on the
Microchip web site.
“MPLAB ICD 2 In-Circuit Debugger User’s
Guide” (DS51331)
“Using MPLAB ICD 2” (poster) (DS51265)
“MPLAB ICD 2 Design Advisory” (DS51566)
“Using MPLAB ICD 3” (poster) (DS51765)
“MPLAB ICD 3 Design Advisory” (DS51764)
“MPLAB REAL ICE In-Circuit Emulator User’s
Guide” (DS51616)
“Using MPLAB REAL ICE In-Circuit Emulator”
(poster) (DS51749)
2.5
External Oscillator Pins
Many microcontrollers have options for at least two
oscillators: a high-frequency primary oscillator and a
low-frequency
secondary
oscillator
(refer
to
The oscillator circuit should be placed on the same
side of the board as the device. Place the oscillator
circuit close to the respective oscillator pins with no
more than 0.5 inch (12 mm) between the circuit
components and the pins. The load capacitors should
be placed next to the oscillator itself, on the same side
of the board.
Use a grounded copper pour around the oscillator
circuit to isolate it from surrounding circuits. The
grounded copper pour should be routed directly to the
MCU ground. Do not run any signal traces or power
traces inside the ground pour. Also, if using a
two-sided board, avoid any traces on the other side of
the board where the crystal is placed. A suggested
layout is shown in Figure 2-3.
For additional information and design guidance on
oscillator circuits, please refer to these Microchip
Application Notes, available at the corporate web site
(www.microchip.com):
AN826, “Crystal Oscillator Basics and Crystal
Selection for rfPIC and PICmicro Devices”
AN849, “Basic PICmicro Oscillator Design”
AN943, “Practical PICmicro Oscillator Analysis
and Design”
AN949, “Making Your Oscillator Work”
FIGURE 2-3:
SUGGESTED PLACEMENT
OF THE OSCILLATOR
CIRCUIT
2.6
Unused I/Os
Unused I/O pins should be configured as outputs and
driven to a logic low state. Alternatively, connect a 1 k
to 10 k resistor to VSS on unused pins and drive the
output to logic low.
13
Main Oscillator
Guard Ring
Guard Trace
Secondary
Oscillator
14
15
16
17
18
19
20
相關PDF資料
PDF描述
PIC24FJ32GB002-I/SP IC MCU 16BIT 32KB FLASH 28DIP
DSPIC33FJ16GP304-I/PT IC DSPIC MCU/DSP 16K 44TQFP
PIC16C62B-20I/SP IC MCU OTP 2KX14 PWM 28DIP
DSPIC30F2010-20I/SP IC DSPIC MCU/DSP 12K 28DIP
AT89S52-24AC IC MCU 8K FLASH 24MHZ 44-TQFP
相關代理商/技術參數
參數描述
PIC18F4321T-I/ML 功能描述:8位微控制器 -MCU 8 KB Flash 512 RAM RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
PIC18F4321T-I/PT 功能描述:8位微控制器 -MCU 8 KB Flash 512 RAM RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
PIC18F4331-E/ML 功能描述:8位微控制器 -MCU 8KB 768 RAM 34 I/O RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
PIC18F4331-E/P 功能描述:8位微控制器 -MCU 8KB 768 RAM 34 I/O RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
PIC18F4331-E/PT 功能描述:8位微控制器 -MCU 8KB 768 RAM 34 I/O RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*