參數資料
型號： PIC16LF627-04/P
廠商： Microchip Technology
文件頁數： 10/170頁
文件大小： 0K
描述： IC MCU FLASH 1KX14 COMP 18DIP
產品培訓模塊： Asynchronous Stimulus
8-bit PIC® Microcontroller Portfolio
標準包裝： 25
系列： PIC® 16F
核心處理器： PIC
芯體尺寸： 8-位
速度： 4MHz
連通性： UART/USART
外圍設備： 欠壓檢測/復位，POR，PWM，WDT
輸入/輸出數： 16
程序存儲器容量： 1.75KB（1K x 14）
程序存儲器類型： 閃存
EEPROM 大小： 128 x 8
RAM 容量： 224 x 8
電壓 - 電源 (Vcc/Vdd)： 2 V ~ 5.5 V
振蕩器型： 內部
工作溫度： 0°C ~ 70°C
封裝/外殼： 18-DIP（0.300"，7.62mm）
包裝： 管件
其它名稱： PIC16LF627-04/PR
PIC16LF627-04/PR-ND
2003 Microchip Technology Inc.
Preliminary
DS40300C-page 105
PIC16F62X
14.9.1
WAKE-UP FROM SLEEP
The device can wake-up from SLEEP through one of
the following events:
1.
External RESET input on MCLR pin
2.
Watchdog Timer Wake-up (if WDT was enabled)
3.
Interrupt from RB0/INT pin, RB Port change, or
the Peripheral Interrupt (Comparator).
The first event will cause a device RESET. The two
latter events are considered a continuation of program
execution. The TO and PD bits in the STATUS register
can be used to determine the cause of device RESET.
PD bit, which is set on power-up is cleared when
SLEEP is invoked. TO bit is cleared if WDT Wake-up
occurred.
When the SLEEP instruction is being executed, the
next instruction (PC + 1) is pre-fetched. For the device
to
wake-up
through
an
interrupt
event,
the
corresponding interrupt enable bit must be set
(enabled). Wake-up is regardless of the state of the
GIE bit. If the GIE bit is clear (disabled), the device con-
tinues execution at the instruction after the SLEEP
instruction. If the GIE bit is set (enabled), the device
executes the instruction after the SLEEP instruction
and then branches to the interrupt address (0004h). In
cases where the execution of the instruction following
SLEEP
is not desirable, the user should have an NOP
after the SLEEP instruction.
The WDT is cleared when the device wakes-up from
SLEEP, regardless of the source of wake-up.
FIGURE 14-17:
WAKE-UP FROM SLEEP THROUGH INTERRUPT
14.10 Code Protection
If
the
code
protection
bit(s)
have
not
been
programmed, the on-chip program memory can be
read out for verification purposes.
14.11 User ID Locations
Four memory locations (2000h-2003h) are designated
as user ID locations where the user can store
checksum or other code-identification numbers. These
locations are not accessible during normal execution
but are readable and writable during program/verify.
Only the Least Significant 4 bits of the user ID locations
are used.
Note:
If the global interrupts are disabled (GIE is
cleared), but any interrupt source has both
its interrupt enable bit and the correspond-
ing interrupt flag bits set, the device will
immediately wake-up from SLEEP. The
SLEEP
instruction is completely executed.
Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1
Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4
OSC1
CLKOUT(4)
INT pin
INTF flag
(INTCON<1>)
GIE bit
(INTCON<7>)
INSTRUCTION FLOW
PC
Instruction
Fetched
Instruction
Executed
PC
PC+1
PC+2
Inst(PC) = SLEEP
Inst(PC - 1)
Inst(PC + 1)
SLEEP
Processor in
SLEEP
Interrupt Latency
(Note 2)
Inst(PC + 2)
Inst(PC + 1)
Inst(0004h)
Inst(0005h)
Inst(0004h)
Dummy cycle
PC + 2
0004h
0005h
Dummy cycle
Tost(2)
PC+2
Note
1: XT, HS or LP Oscillator mode assumed.
2: TOST = 1024TOSC (drawing not to scale). Approximately 1
s delay will be there for ER Osc mode.
3: GIE = '1' assumed. In this case after wake- up, the processor jumps to the interrupt routine. If GIE = '0', execution will continue
in-line.
4: CLKOUT is not available in these Osc modes, but shown here for timing reference.
Note:
The entire data EEPROM and FLASH
program memory will be erased when the
code protection is turned off. The INTRC
calibration data is not erased.
相關PDF資料
PDF描述
PIC18F86J55T-I/PT IC PIC MCU FLASH 48KX16 80TQFP
PIC18F43K22-I/MV MCU PIC 8KB FLASH 40QFN
PIC16C55A-04I/P IC MCU OTP 512X12 28DIP
PIC18LF43K22-I/MV MCU PIC 8KB FLASH 40UQFN
PIC16C622A-20I/P IC MCU OTP 2KX14 COMP 18DIP
相關代理商/技術參數
參數描述
PIC16LF627A-I/ML 功能描述:8位微控制器 -MCU 1.75KB 224 RAM 16I/O Ind Temp QFN28 RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
PIC16LF627A-I/P 功能描述:8位微控制器 -MCU 1.75KB 224 RAM 16I/O Ind Temp PDIP18 RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
PIC16LF627A-I/SO 功能描述:8位微控制器 -MCU 1.75KB 224 RAM 16I/O Ind Temp SOIC18 RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
PIC16LF627A-I/SO 制造商:Microchip Technology Inc 功能描述:8-Bit Microcontroller IC
PIC16LF627A-I/SS 功能描述:8位微控制器 -MCU 1.75KB 224 RAM 16I/O Ind Temp SSOP20 RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*