參數資料
型號： PIC16CR76
廠商： Microchip Technology Inc.
英文描述： 28/40-Pin, 8-Bit CMOS ROM Microcontrollers
中文描述： 28/40-Pin，8位微控制器的CMOS光盤
文件頁數： 89/172頁
文件大?。?/td> 1506K
代理商： PIC16CR76
2007 Microchip Technology Inc.
DS21993C-page 87
PIC16CR7X
11.2
Selecting the A/D Conversion
Clock
The A/D conversion time per bit is defined as T
AD
. The
A/D conversion requires 9.0 T
AD
per 8-bit conversion.
The source of the A/D conversion clock is software
selectable. The four possible options for T
AD
are:
2 T
OSC
(F
OSC
/2)
8 T
OSC
(F
OSC
/8)
32 T
OSC
(F
OSC
/32)
Internal RC oscillator (2-6
μ
s)
For correct A/D conversions, the A/D conversion clock
(T
AD
) must be selected to ensure a minimum T
AD
time
as small as possible, but no less than 1.6
μ
s.
11.3
Configuring Analog Port Pins
The ADCON1, TRISA and TRISE registers control the
operation of the A/D port pins. The port pins that are
desired as analog inputs must have their correspond-
ing TRIS bits set (input). If the TRIS bit is cleared (out-
put), the digital output level (V
OH
or V
OL
) will be
converted.
The A/D operation is independent of the state of the
CHS2:CHS0 bits and the TRIS bits.
11.4
A/D Conversions
Setting the GO/DONE bit begins an A/D conversion.
When the conversion completes, the 8-bit result is
placed in the ADRES register, the GO/DONE bit is
cleared, and the ADIF flag (PIR<6>) is set.
If both the A/D interrupt bit ADIE (PIE1<6>) and the
peripheral interrupt enable bit PEIE (INTCON<6>) are
set, the device will wake from Sleep whenever ADIF is
set by hardware. In addition, an interrupt will also occur
if the Global Interrupt bit GIE (INTCON<7>) is set.
Clearing the GO/DONE bit during a conversion will
abort the current conversion. The ADRES register will
NOT be changed and the ADIF flag will not be set.
After the GO/DONE bit is cleared at either the end of a
conversion, or by firmware, another conversion can be
initiated by setting the GO/DONE bit. Users must still
take into account the appropriate acquisition time for
the application.
11.5
A/D Operation During Sleep
The A/D module can operate during Sleep mode. This
requires that the A/D clock source be set to RC
(ADCS1:ADCS0 =
11
). When the RC clock source is
selected, the A/D module waits one instruction cycle
before starting the conversion. This allows the
SLEEP
instruction to be executed, which eliminates all digital
switching noise from the conversion. When the conver-
sion is completed, the GO/DONE bit will be cleared,
and the result loaded into the ADRES register. If the
A/D interrupt is enabled, the device will wake-up from
Sleep. If the A/D interrupt is not enabled, the A/D
module will then be turned off, although the ADON bit
will remain set.
When the A/D clock source is another clock option (not
RC), a
SLEEP
instruction will cause the present conver-
sion to be aborted and the A/D module to be turned off,
though the ADON bit will remain set.
Turning off the A/D places the A/D module in its lowest
current consumption state.
11.6
Effects of a Reset
A device Reset forces all registers to their Reset state.
The A/D module is disabled and any conversion in
progress is aborted. All A/D input pins are configured
as analog inputs.
The ADRES register will contain unknown data after a
Power-on Reset.
Note 1:
When reading the PORT register, all pins
configured as analog input channels will
read as cleared (a low level). Pins config-
ured as digital inputs will convert an ana-
log input. Analog levels on a digitally
configured input will not affect the conver-
sion accuracy.
2:
Analog levels on any pin that is defined as
a digital input, but not as an analog input,
may cause the digital input buffer to
consume current that is out of the
device’s specification.
Note:
The GO/DONE bit should
NOT
be set in
the same instruction that turns on the A/D.
Note:
For the A/D module to operate in Sleep,
the A/D clock source must be set to RC
(ADCS1:ADCS0 =
11
). To perform an A/D
conversion in Sleep, ensure the
SLEEP
instruction immediately follows the instruc-
tion that sets the GO/DONE bit.
相關PDF資料
PDF描述
PIC16CR77 28/40-Pin, 8-Bit CMOS ROM Microcontrollers
PIC16CR7X 28/40-Pin, 8-Bit CMOS ROM Microcontrollers
PIC16F628A 18-pin Flash-Based 8-Bit CMOS Microcontrollers with nanoWatt Technology(18引腳，基于FLASH的8位CMOS微控制器，使用毫微瓦特技術)
PIC16F687 20-Pin Flash-Based, 8-Bit CMOS Microcontrollers with nanoWatt Technology
PIC16F685 20-Pin Flash-Based, 8-Bit CMOS Microcontrollers with nanoWatt Technology
相關代理商/技術參數
參數描述
PIC16CR76-I/ML 功能描述:IC PIC MCU 8KX14 28QFN RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:PIC® 16C 產品培訓模塊:XLP Deep Sleep Mode 8-bit PIC® Microcontroller Portfolio 標準包裝:22 系列:PIC® XLP™ 18F 核心處理器:PIC 芯體尺寸:8-位 速度:48MHz 連通性:I²C，SPI，UART/USART，USB 外圍設備:欠壓檢測/復位，POR，PWM，WDT 輸入/輸出數:14 程序存儲器容量:8KB（4K x 16） 程序存儲器類型:閃存 EEPROM 大小:256 x 8 RAM 容量:512 x 8 電壓 - 電源 (Vcc/Vdd):1.8 V ~ 5.5 V 數據轉換器:A/D 11x10b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:20-DIP（0.300"，7.62mm） 包裝:管件 產品目錄頁面:642 (CN2011-ZH PDF) 配用:DV164126-ND - KIT DEVELOPMENT USB W/PICKIT 2DM164127-ND - KIT DEVELOPMENT USB 18F14/13K50AC164112-ND - VOLTAGE LIMITER MPLAB ICD2 VPP
PIC16CR76-I/SO 功能描述:IC PIC MCU 8KX14 28SOIC RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:PIC® 16C 產品培訓模塊:XLP Deep Sleep Mode 8-bit PIC® Microcontroller Portfolio 標準包裝:22 系列:PIC® XLP™ 18F 核心處理器:PIC 芯體尺寸:8-位 速度:48MHz 連通性:I²C，SPI，UART/USART，USB 外圍設備:欠壓檢測/復位，POR，PWM，WDT 輸入/輸出數:14 程序存儲器容量:8KB（4K x 16） 程序存儲器類型:閃存 EEPROM 大小:256 x 8 RAM 容量:512 x 8 電壓 - 電源 (Vcc/Vdd):1.8 V ~ 5.5 V 數據轉換器:A/D 11x10b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:20-DIP（0.300"，7.62mm） 包裝:管件 產品目錄頁面:642 (CN2011-ZH PDF) 配用:DV164126-ND - KIT DEVELOPMENT USB W/PICKIT 2DM164127-ND - KIT DEVELOPMENT USB 18F14/13K50AC164112-ND - VOLTAGE LIMITER MPLAB ICD2 VPP
PIC16CR76-I/SP 功能描述:IC PIC MCU 8KX14 28DIP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:PIC® 16C 產品培訓模塊:XLP Deep Sleep Mode 8-bit PIC® Microcontroller Portfolio 標準包裝:22 系列:PIC® XLP™ 18F 核心處理器:PIC 芯體尺寸:8-位 速度:48MHz 連通性:I²C，SPI，UART/USART，USB 外圍設備:欠壓檢測/復位，POR，PWM，WDT 輸入/輸出數:14 程序存儲器容量:8KB（4K x 16） 程序存儲器類型:閃存 EEPROM 大小:256 x 8 RAM 容量:512 x 8 電壓 - 電源 (Vcc/Vdd):1.8 V ~ 5.5 V 數據轉換器:A/D 11x10b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:20-DIP（0.300"，7.62mm） 包裝:管件 產品目錄頁面:642 (CN2011-ZH PDF) 配用:DV164126-ND - KIT DEVELOPMENT USB W/PICKIT 2DM164127-ND - KIT DEVELOPMENT USB 18F14/13K50AC164112-ND - VOLTAGE LIMITER MPLAB ICD2 VPP
PIC16CR76-I/SS 功能描述:IC PIC MCU 8KX14 28SSOP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:PIC® 16C 產品培訓模塊:XLP Deep Sleep Mode 8-bit PIC® Microcontroller Portfolio 標準包裝:22 系列:PIC® XLP™ 18F 核心處理器:PIC 芯體尺寸:8-位 速度:48MHz 連通性:I²C，SPI，UART/USART，USB 外圍設備:欠壓檢測/復位，POR，PWM，WDT 輸入/輸出數:14 程序存儲器容量:8KB（4K x 16） 程序存儲器類型:閃存 EEPROM 大小:256 x 8 RAM 容量:512 x 8 電壓 - 電源 (Vcc/Vdd):1.8 V ~ 5.5 V 數據轉換器:A/D 11x10b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:20-DIP（0.300"，7.62mm） 包裝:管件 產品目錄頁面:642 (CN2011-ZH PDF) 配用:DV164126-ND - KIT DEVELOPMENT USB W/PICKIT 2DM164127-ND - KIT DEVELOPMENT USB 18F14/13K50AC164112-ND - VOLTAGE LIMITER MPLAB ICD2 VPP
PIC16CR76T-I/ML 功能描述:IC PIC MCU 8KX14 28QFN RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:PIC® 16C 產品培訓模塊:XLP Deep Sleep Mode 8-bit PIC® Microcontroller Portfolio 標準包裝:22 系列:PIC® XLP™ 18F 核心處理器:PIC 芯體尺寸:8-位 速度:48MHz 連通性:I²C，SPI，UART/USART，USB 外圍設備:欠壓檢測/復位，POR，PWM，WDT 輸入/輸出數:14 程序存儲器容量:8KB（4K x 16） 程序存儲器類型:閃存 EEPROM 大小:256 x 8 RAM 容量:512 x 8 電壓 - 電源 (Vcc/Vdd):1.8 V ~ 5.5 V 數據轉換器:A/D 11x10b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:20-DIP（0.300"，7.62mm） 包裝:管件 產品目錄頁面:642 (CN2011-ZH PDF) 配用:DV164126-ND - KIT DEVELOPMENT USB W/PICKIT 2DM164127-ND - KIT DEVELOPMENT USB 18F14/13K50AC164112-ND - VOLTAGE LIMITER MPLAB ICD2 VPP
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*