參數資料
型號： PIC16C772
廠商： Microchip Technology Inc.
英文描述： Mixed Signal OTP Microcontroller(工作電壓3.0~5.5V，捕捉/比較/PWM的微控制器)
中文描述： 檢察官辦公室的混合信號微控制器（工作電壓3.0?5.5V之間，捕捉/比較/脈寬調制的微控制器）
文件頁數： 104/170頁
文件大?。?/td> 4191K
代理商： PIC16C772
PIC16F62X
DS40300C-page 102
Preliminary
2003 Microchip Technology Inc.
14.6.1
RB0/INT INTERRUPT
External interrupt on RB0/INT pin is edge triggered:
either rising if INTEDG bit (OPTION<6>) is set, or
falling, if INTEDG bit is clear. When a valid edge
appears on the RB0/INT pin, the INTF bit
(INTCON<1>) is set. This interrupt can be disabled by
clearing the INTE control bit (INTCON<4>). The INTF
bit must be cleared in software in the interrupt service
routine before re-enabling this interrupt. The RB0/INT
interrupt can wake-up the processor from SLEEP, if the
INTE bit was set prior to going into SLEEP. The status
of the GIE bit decides whether or not the processor
branches to the interrupt vector following wake-up. See
Section 14.9 for details on SLEEP, and Figure 14-17
for timing of wake-up from SLEEP through RB0/INT
interrupt.
14.6.2
TMR0 INTERRUPT
An overflow (FFh
→
00h) in the TMR0 register will
set the T0IF (INTCON<2>) bit. The interrupt can
be
enabled/disabled
by
(INTCON<5>) bit. For operation of the Timer0 module,
see Section 6.0.
setting/clearing
T0IE
14.6.3
PORTB INTERRUPT
An input change on PORTB <7:4> sets the RBIF
(INTCON<0>) bit. The interrupt can be enabled/
disabled by setting/clearing the RBIE (INTCON<4>)
bit. For operation of PORTB (Section 5.2).
14.6.4
COMPARATOR INTERRUPT
See Section 9.6 for complete description of comparator
interrupts.
FIGURE 14-15:
INT PIN INTERRUPT TIMING
Note:
If a change on the I/O pin should occur
when the read operation is being executed
(start of the Q2 cycle), then the RBIF inter-
rupt flag may not get set.
Q2
Q1
Q3
Q4
Q2
Q1
Q3
Q4
Q2
Q1
Q3
Q4
Q2
Q1
Q3
Q4
Q2
Q1
Q3
Q4
OSC1
CLKOUT
INT pin
INTF flag
(INTCON<1>)
GIE bit
(INTCON<7>)
INSTRUCTION FLOW
PC
Instruction
Fetched
Instruction
Executed
Interrupt Latency
PC
PC+1
PC+1
0004h
0005h
Inst (0004h)
Inst (0005h)
Dummy Cycle
Inst (PC)
Inst (PC+1)
Inst (PC-1)
Inst (0004h)
Dummy Cycle
Inst (PC)
—
Note
1:
2:
INTF flag is sampled here (every Q1).
Asynchronous interrupt latency = 3-4 Tcy. Synchronous latency = 3 Tcy, where Tcy = instruction cycle time. Latency
is the same whether Inst (PC) is a single cycle or a 2-cycle instruction.
CLKOUT is available in ER and INTRC Oscillator mode.
For minimum width of INT pulse, refer to AC specs.
INTF is enabled to be set anytime during the Q4-Q1 cycles.
3:
4:
5:
(1)
(1)
(4)
(5)
(2)
(3)
相關PDF資料
PDF描述
PIC16C773 Mixed Signal OTP Microcontroller(工作電壓3.0~5.5V，捕捉/比較/PWM的微控制器)
PIC16F873 Enhanced FLASH/EEPROM 8-Bit Microcontroller With A/D Module
PIC16F874 Enhanced FLASH/EEPROM 8-Bit Microcontroller With A/D Module(驅動/吸收電流高，工作電壓2.5~5.5V，微控制器)
PIC17C762 80/84-Pin 8-Bit OTP High-Performance Microcontroller with 10-Bit A/D(4路捕捉，3路PWM，工作電流3.0~5.5V的微控制器)
PIC17C766 80/84-Pin 8-Bit OTP High-Performance Microcontroller with 10-Bit A/D(4路捕捉，3路PWM，工作電流3.0~5.5V的微控制器)
相關代理商/技術參數
參數描述
PIC16C77-20/L 功能描述:8位微控制器 -MCU 14KB 368 RAM 33 I/O RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
PIC16C77-20/L 制造商:Microchip Technology Inc 功能描述:8BIT CMOS MCU SMD 16C77 PLCC44
PIC16C77-20/P 功能描述:8位微控制器 -MCU 14KB 368 RAM 33 I/O RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
PIC16C77-20/P 制造商:Microchip Technology Inc 功能描述:IC 8BIT CMOS MCU 16C77 DIP40
PIC16C77-20/PQ 功能描述:8位微控制器 -MCU 14KB 368 RAM 33 I/O RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*