![](http://datasheet.mmic.net.cn/260000/PIC16C63_datasheet_15942805/PIC16C63_48.png)
PIC16C6X
DS30234D-page 48
1997 Microchip Technology Inc.
4.3
PCL and PCLATH
The program counter (PC) is 13-bits wide. The low byte
comes from the PCL register, which is a readable and
writable register. The upper bits (PC<12:8>) are not
readable, but are indirectly writable through the
PCLATH register. On any reset, the upper bits of the PC
will be cleared. Figure 4-24 shows the two situations for
the loading of the PC. The upper example in the figure
shows how the PC is loaded on a write to PCL
(PCLATH<4:0>
→
PCH). The lower example in the fig-
ure shows how the PC is loaded during a
CALL
or
GOTO
instruction (PCLATH<4:3>
→
PCH).
FIGURE 4-24: LOADING OF PC IN
DIFFERENT SITUATIONS
4.3.1
COMPUTED GOTO
A computed GOTO is accomplished by adding an offset
to the program counter (
ADDWF PCL
). When doing a
table read using a computed GOTO method, care
should be exercised if the table location crosses a PCL
memory boundary (each 256 word block). Refer to the
application note “Implementing a Table Read”(AN556).
4.3.2
STACK
The PIC16CXX family has an 8 deep x 13-bit wide
hardware stack. The stack space is not part of either
program or data space and the stack pointer is not
readable or writable. The PC is PUSHed onto the stack
when a
CALL
instruction is executed or an interrupt
causes a branch. The stack is POPed in the event of a
RETURN, RETLW
or a
RETFIE
instruction execution.
PCLATH is not affected by a PUSH or a POP operation.
The stack operates as a circular buffer. This means that
after the stack has been PUSHed eight times, the ninth
push overwrites the value that was stored from the first
push. The tenth push overwrites the second push (and
so on).
Applicable Devices
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
PC
12
8
7
0
5
PCLATH<4:0>
PCLATH
Instruction with
PCL as
destination
ALU
GOTO, CALL
Opcode <10:0>
8
PC
12
11 10
0
11
PCLATH<4:3>
PCH
PCL
8
7
2
PCLATH
PCH
PCL
4.4
Program Memory Paging
PIC16C6X devices are capable of addressing a contin-
uous 8K word block of program memory. The
CALL
and
GOTO
instructions provide only 11 bits of address to
allow branching within any 2K program memory page.
When doing a
CALL
or
GOTO
instruction the upper two
bits of the address are provided by PCLATH<4:3>.
When doing a
CALL
or
GOTO
instruction, the user must
ensure that the page select bits are programmed so
that the desired program memory page is addressed. If
a return from a
CALL
instruction (or interrupt) is exe-
cuted, the entire 13-bit PC is pushed onto the stack.
Therefore, manipulation of the PCLATH<4:3> bits are
not required for the return instructions (which POPs the
address from the stack).
Note 1:
There are no status bits to indicate stack
overflows or stack underflow conditions.
Note 2:
There are no instructions mnemonics
called PUSH or POP. These are actions
that occur from the execution of the
CALL,
RETURN, RETLW,
and
RETFIE
instruc-
tions, or the vectoring to an interrupt
address
Applicable Devices
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
Note:
PIC16C6X devices with 4K or less of pro-
gram
memory
ignore
PCLATH<4>. The use of PCLATH<4> as a
general purpose read/write bit is not rec-
ommended since this may affect upward
compatibility with future products.
paging
bit