參數資料
型號: PIC16C505-20E/P
廠商: Microchip Technology
文件頁數: 18/90頁
文件大?。?/td> 0K
描述: IC MCU OTP 1KX12 14DIP
產品培訓模塊: Asynchronous Stimulus
標準包裝: 30
系列: PIC® 16C
核心處理器: PIC
芯體尺寸: 8-位
速度: 20MHz
外圍設備: POR,WDT
輸入/輸出數: 11
程序存儲器容量: 1.5KB(1K x 12)
程序存儲器類型: OTP
RAM 容量: 72 x 8
電壓 - 電源 (Vcc/Vdd): 3 V ~ 5.5 V
振蕩器型: 內部
工作溫度: -40°C ~ 125°C
封裝/外殼: 14-DIP(0.300",7.62mm)
包裝: 管件
配用: 309-1086-ND - ADAPTER 14-ZIF BD W/14-SO PLUGS
309-1085-ND - ADAPTER 14-DIP BD W/2 14-SO PLUG
1999-2012 Microchip Technology Inc.
DS40192D-page 25
PIC16C505
6.1
Using Timer0 with an External Clock
When an external clock input is used for Timer0, it
must meet certain requirements. The external clock
requirement is due to internal phase clock (TOSC)
synchronization. Also, there is a delay in the actual
incrementing of Timer0 after synchronization.
6.1.1
EXTERNAL CLOCK SYNCHRONIZATION
When no prescaler is used, the external clock input is
the same as the prescaler output. The synchronization
of
T0CKI
with
the
internal
phase
clocks
is
accomplished by sampling the prescaler output on the
Q2 and Q4 cycles of the internal phase clocks
(Figure 6-4). Therefore, it is necessary for T0CKI to be
high for at least 2TOSC (and a small RC delay of 20 ns)
and low for at least 2TOSC (and a small RC delay of
20 ns). Refer to the electrical specification of the
desired device.
When a prescaler is used, the external clock input is
divided by the asynchronous ripple counter-type
prescaler, so that the prescaler output is symmetrical.
For
the
external
clock
to
meet
the
sampling
requirement, the ripple counter must be taken into
account. Therefore, it is necessary for T0CKI to have a
period of at least 4TOSC (and a small RC delay of
40 ns) divided by the prescaler value. The only
requirement on T0CKI high and low time is that they
do not violate the minimum pulse width requirement of
10 ns. Refer to parameters 40, 41 and 42 in the
electrical specification of the desired device.
6.1.2
TIMER0 INCREMENT DELAY
Since the prescaler output is synchronized with the
internal clocks, there is a small delay from the time the
external clock edge occurs to the time the Timer0
module is actually incremented. Figure 6-4 shows the
delay from the external clock edge to the timer
incrementing.
FIGURE 6-4:
TIMER0 TIMING WITH EXTERNAL CLOCK
Increment Timer0 (Q4)
External Clock Input or
Q1
Q2
Q3 Q4
Q1
Q2
Q3 Q4
Q1
Q2
Q3 Q4
Q1
Q2
Q3 Q4
Timer0
T0
T0 + 1
T0 + 2
Small pulse
misses sampling
External Clock/Prescaler
Output After Sampling
(3)
Note 1:
2:
3:
Delay from clock input change to Timer0 increment is 3Tosc to 7Tosc. (Duration of Q = Tosc).
Therefore, the error in measuring the interval between two edges on Timer0 input =
4Tosc max.
External clock if no prescaler selected; prescaler output otherwise.
The arrows indicate the points in time where sampling occurs.
Prescaler Output (2)
(1)
相關PDF資料
PDF描述
PIC12LCE518-04I/SN IC MCU OTP 512X12 LV W/EE 8SOIC
VE-23F-CV-S CONVERTER MOD DC/DC 72V 150W
VE-23D-CV-S CONVERTER MOD DC/DC 85V 150W
VE-23B-CV-S CONVERTER MOD DC/DC 95V 150W
VE-233-CV-S CONVERTER MOD DC/DC 24V 150W
相關代理商/技術參數
參數描述
PIC16C505-20I/P 功能描述:8位微控制器 -MCU 1.5KB 72 RAM 12 I/O 20MHz IndTemp PDIP14 RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
PIC16C505-20I/P 制造商:Microchip Technology Inc 功能描述:IC 8BIT CMOS MCU 16C505 DIP14
PIC16C505-20I/SL 功能描述:8位微控制器 -MCU 1.5KB 72 RAM 12 I/O 20MHz IndTemp SOIC14 RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
PIC16C505-20I/SL 制造商:Microchip Technology Inc 功能描述:8BIT CMOS MCU SMD 16C505 SOIC14
PIC16C505T-04/SL 功能描述:8位微控制器 -MCU 1.5KB 72 RAM 12 I/O 4MHz SOIC14 RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT