- 您現在的位置：買賣IC網 > PDF目錄365366 > PIC12F681 (Microchip Technology Inc.) 8-Pin, 8-Bit CMOS Enhanced FLASH Microcontroller with Serial I/O Interface(-2.0~5.5V,串行I/O接口,閃速微控制器) PDF資料下載
參數資料
| 型號： | PIC12F681 |
| 廠商： | Microchip Technology Inc. |
| 英文描述： | 8-Pin, 8-Bit CMOS Enhanced FLASH Microcontroller with Serial I/O Interface(-2.0~5.5V,串行I/O接口,閃速微控制器) |
| 中文描述： | 8引腳，8位串行我的CMOS增強型閃存微控制器/ O接口（-2.0?5.5V的，串行的I / O接口，閃速微控制器） |
| 文件頁數： | 85/170頁 |
| 文件大小： | 4191K |
| 代理商： | PIC12F681 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁當前第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁
2003 Microchip Technology Inc.
Preliminary
DS40300C-page 83
PIC16F62X
12.4.2
USART SYNCHRONOUS MASTER
RECEPTION
Once Synchronous mode is selected, reception is
enabled
by
setting
either
(RCSTA<5>) or enable bit CREN (RCSTA<4>). Data is
sampled on the RB1/RX/DT pin on the falling edge of
the clock. If enable bit SREN is set, then only a single
word is received. If enable bit CREN is set, the recep-
tion is continuous until CREN is cleared. If both bits are
set, then CREN takes precedence. After clocking the
last bit, the received data in the Receive Shift Register
(RSR) is transferred to the RCREG register (if it is
empty). When the transfer is complete, interrupt flag bit
RCIF (PIR1<5>) is set. The actual interrupt can be
enabled/disabled by setting/clearing enable bit RCIE
(PIE1<5>). Flag bit RCIF is a read only bit which is
RESET by the hardware. In this case, it is RESET
when the RCREG register has been read and is empty.
The RCREG is a double buffered register (i.e., it is a
two-deep FIFO). It is possible for two bytes of data to
be received and transferred to the RCREG FIFO and a
third byte to begin shifting into the RSR register. On the
clocking of the last bit of the third byte, if the RCREG
register is still full then overrun error bit OERR
(RCSTA<1>) is set. The word in the RSR will be lost.
The RCREG register can be read twice to retrieve the
two bytes in the FIFO. Bit OERR has to be cleared in
software (by clearing bit CREN). If bit OERR is set,
transfers from the RSR to the RCREG are inhibited, so
it is essential to clear bit OERR if it is set. The 9th
enable
bit
SREN
receive bit is buffered the same way as the receive
data. Reading the RCREG register, will load bit RX9D
with a new value, therefore it is essential for the user to
read the RCSTA register before reading RCREG in
order not to lose the old RX9D information.
Steps to follow when setting up a Synchronous Master
Reception:
1.
Initialize the SPBRG register for the appropriate
baud rate. (Section 12.1)
2.
Enable the synchronous master serial port by
setting bits SYNC, SPEN, and CSRC.
3.
Ensure bits CREN and SREN are clear.
4.
If interrupts are desired, then set enable bit
RCIE.
5.
If 9-bit reception is desired, then set bit RX9.
6.
If a single reception is required, set bit SREN.
For continuous reception set bit CREN.
7.
Interrupt flag bit RCIF will be set when reception
is complete and an interrupt will be generated if
enable bit RCIE was set.
8.
Read the RCSTA register to get the ninth bit (if
enabled) and determine if any error occurred
during reception.
9.
Read the 8-bit received data by reading the
RCREG register.
10. If any error occurred, clear the error by clearing
bit CREN.
TABLE 12-10: REGISTERS ASSOCIATED WITH SYNCHRONOUS MASTER RECEPTION
Address
Name
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Value on:
POR
Value on all
other
RESETS
0Ch
PIR1
EEIF
CMIF
RCIF
TXIF
—
CCP1IF TMR2IF
TMR1IF
0000 -000
RX9D
0000 -00x
0000 0000
0000 -000
0000 -00x
0000 0000
-000 -000
0000 -010
0000 0000
18h
RCSTA
SPEN
RX9
SREN CREN
ADEN
FERR
OERR
1Ah
RCREG USART Receive Register
8Ch
PIE1
EEPIE
CMIE
RCIE
TXIE
—
CCP1IE TMR2IE TMR1IE
-000 0000
BRGH
TRMT
98h
TXSTA
CSRC
TX9
TXEN
SYNC
—
TX9D
0000 -010
0000 0000
99h
Legend:
x
= unknown,
-
= unimplemented read as '0'. Shaded cells are not used for Synchronous Master Reception.
SPBRG Baud Rate Generator Register
相關PDF資料 |
PDF描述 |
|---|---|
| PIC16C164 | OTP 8-Bit High-Performance CMOS Microcontroller(主從模式，工作電壓3.0~5.5V，2路PWM的微控制器) |
| PIC16C165 | OTP 8-Bit High-Performance CMOS Microcontroller(主從模式，工作電壓3.0~5.5V，2路PWM的微控制器) |
| PIC16C174 | OTP 8-Bit High-Performance CMOS Microcontroller(主從模式，工作電壓3.0~5.5V，2路PWM的微控制器) |
| PIC16C175 | OTP 8-Bit High-Performance CMOS Microcontroller(主從模式，工作電壓3.0~5.5V，2路PWM的微控制器) |
| PIC16C176 | OTP 8-Bit High-Performance CMOS Microcontroller(主從模式，工作電壓3.0~5.5V，2路PWM的微控制器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PIC12F683 | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:8-Pin Flash-Based, 8-Bit CMOS Microcontrollers with nanoWatt Technology |
| PIC12F683 DEVELOPMENT BOARD KIT | 制造商:Custom Computer Services (CCS) 功能描述:BOARD DEV FOR PIC12F683 |
| PIC12F683 DEVELOPMENT KIT | 功能描述:KIT DEV EMBEDDED C RoHS:否 類別:編程器，開發系統 >> 通用嵌入式開發板和套件（MCU、DSP、FPGA、CPLD等） 系列:- 標準包裝:1 系列:PICDEM™ 類型:MCU 適用于相關產品:PIC10F206，PIC16F690，PIC16F819 所含物品:板，線纜，元件，CD，PICkit 編程器 產品目錄頁面:659 (CN2011-ZH PDF) |
| PIC12F683_07 | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:8-Pin Flash-Based, 8-Bit CMOS Microcontrollers with nanoWatt Technology |
| PIC12F683-E/MD | 功能描述:8位微控制器 -MCU 3.5KB 128 RAM 6I/O RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。