- 您現在的位置：買賣IC網 > PDF目錄3895 > PIC12F675T-I/SN (Microchip Technology)IC MCU CMOS 1K FLASH W/AD 8-SOIC PDF資料下載
參數資料
| 型號： | PIC12F675T-I/SN |
| 廠商： | Microchip Technology |
| 文件頁數： | 5/35頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC MCU CMOS 1K FLASH W/AD 8-SOIC |
| 產品培訓模塊： | Asynchronous Stimulus 8-bit PIC® Microcontroller Portfolio |
| 標準包裝： | 3,300 |
| 系列： | PIC® 12F |
| 核心處理器： | PIC |
| 芯體尺寸： | 8-位 |
| 速度： | 20MHz |
| 外圍設備： | POR，WDT |
| 輸入/輸出數： | 5 |
| 程序存儲器容量： | 1.75KB（1K x 14） |
| 程序存儲器類型： | 閃存 |
| EEPROM 大?。?/td> | 128 x 8 |
| RAM 容量： | 64 x 8 |
| 電壓 - 電源 (Vcc/Vdd)： | 2 V ~ 5.5 V |
| 數據轉換器： | A/D 4x10b |
| 振蕩器型： | 內部 |
| 工作溫度： | -40°C ~ 85°C |
| 封裝/外殼： | 8-SOIC（0.154"，3.90mm 寬） |
| 包裝： | 帶卷 (TR) |
| 其它名稱： | PIC12F675-I/SNTR PIC12F675-I/SNTR-ND PIC12F675T-I/SN-ND PIC12F675T-I/SNTR Q1324216 |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁
13
AT89S53
0787E–MICRO–3/06
Baud Rate Generator
Timer 2 is selected as the baud rate generator by setting
TCLK and/or RCLK in T2CON (Table 2). Note that the baud
rates for transmit and receive can be different if Timer 2 is
used for the receiver or transmitter and Timer 1 is used for
the other function. Setting RCLK and/or TCLK puts Timer 2
into its baud rate generator mode, as shown in Figure 4.
The baud rate generator mode is similar to the auto-reload
mode, in that a rollover in TH2 causes the Timer 2 registers
to be reloaded with the 16-bit value in registers RCAP2H
and RCAP2L, which are preset by software.
The baud rates in Modes 1 and 3 are determined by Timer
2’s overflow rate according to the following equation.
The Timer can be configured for either timer or counter
operation. In most applications, it is configured for timer
operation (CP/T2 = 0). The timer operation is different for
Timer 2 when it is used as a baud rate generator. Normally,
as a timer, it increments every machine cycle (at 1/12 the
oscillator frequency). As a baud rate generator, however, it
increments every state time (at 1/2 the oscillator fre-
quency). The baud rate formula is given below.
where (RCAP2H, RCAP2L) is the content of RCAP2H and
RCAP2L taken as a 16-bit unsigned integer.
Timer 2 as a baud rate generator is shown in Figure 4. This
figure is valid only if RCLK or TCLK = 1 in T2CON. Note
that a rollover in TH2 does not set TF2 and will not gener-
ate an interrupt. Note too, that if EXEN2 is set, a 1-to-0
transition in T2EX will set EXF2 but will not cause a reload
from (RCAP2H, RCAP2L) to (TH2, TL2). Thus when Timer
2 is in use as a baud rate generator, T2EX can be used as
an extra external interrupt.
Note that when Timer 2 is running (TR2 = 1) as a timer in
the baud rate generator mode, TH2 or TL2 should not be
read from or written to. Under these conditions, the Timer is
incremented every state time, and the results of a read or
write may not be accurate. The RCAP2 registers may be
read but should not be written to, because a write might
overlap a reload and cause write and/or reload errors. The
timer should be turned off (clear TR2) before accessing the
Timer 2 or RCAP2 registers.
Programmable Clock Out
A 50% duty cycle clock can be programmed to come out on
P1.0, as shown in Figure 5. This pin, besides being a regu-
lar I/0 pin, has two alternate functions. It can be
programmed to input the external clock for Timer/Counter 2
or to output a 50% duty cycle clock ranging from 61 Hz to 4
MHz at a 16 MHz operating frequency.
To configure the Timer/Counter 2 as a clock generator, bit
C/T2 (T2CON.1) must be cleared and bit T2OE (T2MOD.1)
must be set. Bit TR2 (T2CON.2) starts and stops the timer.
The clock-out frequency depends on the oscillator fre-
quency and the reload value of Timer 2 capture registers
(RCAP2H, RCAP2L), as shown in the following equation.
In the clock-out mode, Timer 2 rollovers will not generate
an interrupt. This behavior is similar to when Timer 2 is
used as a baud-rate generator. It is possible to use Timer 2
as a baud-rate generator and a clock generator simulta-
neously. Note, however, that the baud-rate and clock-out
frequencies cannot be determined independently from one
another since they both use RCAP2H and RCAP2L.
Modes 1 and 3 Baud Rates
Timer 2 Overflow Rate
16
------------------------------------------------------------
=
Modes 1 and 3
Baud Rate
---------------------------------------
Oscillator Frequency
32
65536
RCAP2H,RCAP2L
()
–
[]
×
----------------------------------------------------------------------------------------------
=
Clock-Out Frequency
Oscillator Frequency
4
65536
RCAP2H,RCAP2L
()
–
[]
×
-------------------------------------------------------------------------------------------
=
相關PDF資料 |
PDF描述 |
|---|---|
| PIC12F509-I/SM | IC PIC MCU FLASH 1KX12 8-SOIJ |
| PIC12F509-I/P | IC MCU FLASH 1KX12 8DIP |
| 006208512210000 | CONN FFC/FPC 12POS 1MM ZIF SMD |
| PIC16F506-I/SL | IC PIC MCU FLASH 1.5KB 14SOIC |
| PIC12F509-I/MC | IC PIC MCU FLASH 1024X12 8DFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PIC12F683 | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:8-Pin Flash-Based, 8-Bit CMOS Microcontrollers with nanoWatt Technology |
| PIC12F683 DEVELOPMENT BOARD KIT | 制造商:Custom Computer Services (CCS) 功能描述:BOARD DEV FOR PIC12F683 |
| PIC12F683 DEVELOPMENT KIT | 功能描述:KIT DEV EMBEDDED C RoHS:否 類別:編程器，開發系統 >> 通用嵌入式開發板和套件（MCU、DSP、FPGA、CPLD等） 系列:- 標準包裝:1 系列:PICDEM™ 類型:MCU 適用于相關產品:PIC10F206，PIC16F690，PIC16F819 所含物品:板，線纜，元件，CD，PICkit 編程器 產品目錄頁面:659 (CN2011-ZH PDF) |
| PIC12F683_07 | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:8-Pin Flash-Based, 8-Bit CMOS Microcontrollers with nanoWatt Technology |
| PIC12F683-E/MD | 功能描述:8位微控制器 -MCU 3.5KB 128 RAM 6I/O RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。