參數資料
型號: PIC12F1501-I/MF
廠商: Microchip Technology
文件頁數: 10/33頁
文件大小: 0K
描述: IC MCU 8BIT 1.75KB FLASH 8-DFN
標準包裝: 120
系列: PIC® 12F
核心處理器: PIC
芯體尺寸: 8-位
速度: 20MHz
外圍設備: 欠壓檢測/復位,POR,PWM,WDT
輸入/輸出數: 5
程序存儲器容量: 1.75KB(1K x 14)
程序存儲器類型: 閃存
RAM 容量: 64 x 8
電壓 - 電源 (Vcc/Vdd): 2.3 V ~ 5.5 V
數據轉換器: A/D 4x10b
振蕩器型: 內部
工作溫度: -40°C ~ 85°C
封裝/外殼: 8-VDFN 裸露焊盤
包裝: 管件
PIC12(L)F1501
DS41615A-page 18
Preliminary
2011 Microchip Technology Inc.
3.2.1.1
STATUS Register
The STATUS register, shown in Register 3-1, contains:
the arithmetic status of the ALU
the Reset status
The STATUS register can be the destination for any
instruction, like any other register. If the STATUS
register is the destination for an instruction that affects
the Z, DC or C bits, then the write to these three bits is
disabled. These bits are set or cleared according to the
device logic. Furthermore, the TO and PD bits are not
writable. Therefore, the result of an instruction with the
STATUS register as destination may be different than
intended.
For example, CLRF STATUS will clear the upper three
bits and set the Z bit. This leaves the STATUS register
as ‘000u u1uu’ (where u = unchanged).
It is recommended, therefore, that only BCF, BSF,
SWAPF and MOVWF instructions are used to alter the
STATUS register, because these instructions do not
affect any Status bits. For other instructions not
affecting any Status bits (Refer to Section 26.0
Note 1: The C and DC bits operate as Borrow
and Digit Borrow out bits, respectively, in
subtraction.
REGISTER 3-1:
STATUS: STATUS REGISTER
U-0
R-1/q
R/W-0/u
TO
PD
ZDC(1)
C(1)
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
u = Bit is unchanged
x = Bit is unknown
-n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set
‘0’ = Bit is cleared
q = Value depends on condition
bit 7-5
Unimplemented: Read as ‘0’
bit 4
TO: Time-Out bit
1 = After power-up, CLRWDT instruction or SLEEP instruction
0 = A WDT time-out occurred
bit 3
PD: Power-Down bit
1 = After power-up or by the CLRWDT instruction
0 = By execution of the SLEEP instruction
bit 2
Z: Zero bit
1 = The result of an arithmetic or logic operation is zero
0 = The result of an arithmetic or logic operation is not zero
bit 1
DC: Digit Carry/Digit Borrow bit (ADDWF, ADDLW, SUBLW, SUBWF instructions)(1)
1 = A carry-out from the 4th low-order bit of the result occurred
0 = No carry-out from the 4th low-order bit of the result
bit 0
C: Carry/Borrow bit(1) (ADDWF, ADDLW, SUBLW, SUBWF instructions)(1)
1 = A carry-out from the Most Significant bit of the result occurred
0 = No carry-out from the Most Significant bit of the result occurred
Note 1:
For Borrow, the polarity is reversed. A subtraction is executed by adding the two’s complement of the
second operand. For rotate (RRF, RLF) instructions, this bit is loaded with either the high-order or low-order
bit of the source register.
相關PDF資料
PDF描述
PIC12F510-I/MC IC PIC MCU FLASH 1024X12 8DFN
PIC12F629T-I/MF IC MCU CMOS 8BIT 1K FLASH 8-DFN
PIC12LF1501-E/MS IC MCU 8BIT 1.75KB FLASH 8MSOP
PIC16F57-I/SS IC MCU FLASH 2KX12 28SSOP
PIC12F510-I/MS IC PIC MCU FLASH 1.5KB 8MSOP
相關代理商/技術參數
參數描述
PIC12F1501-I-MG 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:14-Pin Flash, 8-Bit Microcontrollers
PIC12F1501T-EMCQTP 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:8-Pin Flash, 8-Bit Microcontrollers
PIC12F1501T-EMCSQTP 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:8-Pin Flash, 8-Bit Microcontrollers
PIC12F1501T-EMFQTP 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:8-Pin Flash, 8-Bit Microcontrollers
PIC12F1501T-EMFSQTP 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:8-Pin Flash, 8-Bit Microcontrollers