
PI74FCT16541/162541/162H541T
16-BIT BUFFER/LINE DRIVERS
PI74FCT162541T
PI74FCT162H541T
229
PS2037A 03/11/96
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012
Logic Block Diagram
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012
Fast CMOS 16-Bit Octal
Buffer/Line Drivers
Product Description
Pericom Semiconductor’s PI74FCT series of logic circuits are pro-
duced in the Company’s advanced 0.6/0.8 micron CMOS technology,
achieving industry leading speed grades.
The PI74FCT16541T, PI74FCT162541T, and PI74FCT162H541T
are non-inverting 16-bit buffer/line drivers designed for applications
driving high capacitance loads and low impedance backplanes.
These high-speed, low-power devices offer bus/backplane interface
capability and a flow-through organization for ease of board layout.
They are designed with three-state controls to operate in a Dual-
Byte, or a single 16-bit word mode.
The PI74FCT16541T output buffers are designed with a Power-
Off disable allowing “l(fā)ive insertion” of boards when used as
backplane drivers.
The PI74FCT162541T has ±24 mA balanced output drivers. It is
designed with current limiting resistors at its outputs to control the
output edge rate resulting in lower ground bounce and undershoot.
This eliminates the need for external terminating resistors for most
interface applications.
The PI74FCT162H541T has “Bus Hold” which retains the input’s
last state whenever the input goes to high-impedance preventing
“floating” inputs and eliminating the need for pull-up/down resistors.
Product Features
Common Features
PI74FCT16541T, PI74FCT162541T, and
PI74FCT162H541T are high-speed,
low power devices with high current drive
V
CC
= 5V ±10%
Hysteresis on all inputs
Packages available
– 48-pin 240 mil wide plastic TSSOP (A48)
– 48-pin 300 mil wide plastic SSOP (V48)
PI74FCT16541T Features
High output drive: I
OH
= –32 mA; I
OL
= 64 mA
Power off disable outputs permit “l(fā)ive insertion”
Typical V
OLP
(Output Ground Bounce) < 1.0V
at V
CC
= 5V, T
A
= 25°C
PI74FCT162541T Features
Balanced output drivers: ±24 mA
Reduced system switching noise
Typical V
OLP
(Output Ground Bounce) < 0.6V
at V
CC
= 5V, T
A
= 25°C
PI74FCT162H541T Features
Bus Hold retains last active bus state during 3-state
Eliminates the need for external pull-up resistors
1
OE
A
1
A
0
1
Y
0
1
OE
B
1
A
1
1
Y
1
1
A
2
1
Y
2
1
A
3
1
Y
3
1
A
4
1
Y
4
1
A
5
1
Y
5
1
A
6
1
Y
6
1
A
7
1
Y
7
2
OE
A
2
A
0
2
Y
0
2
OE
B
2
A
1
2
Y
1
2
A
2
2
Y
2
2
A
3
2
Y
3
2
A
4
2
Y
4
2
A
5
2
Y
5
2
A
6
2
Y
6
2
A
7
2
Y
7