參數資料
型號： PG19IS
英文描述： Monitor_ICs:88P6232 7045 SAM9222G PG17/19 TNY254P 52748 KS2501B-10 KA2507
中文描述： Monitor_ICs：88P6232 7045 SAM9222G PG17/19 TNY254P 52748 KS2501B - 10 KA2507
文件頁數： 9/100頁
文件大?。?/td> 3595K
代理商： PG19IS
4-1-1 Before Making Adjustments
4-1-1 (a) ORIENTATION
When servicing, always face the monitor to the
east.
4-1-1 (b) MAGNETIC FIELDS
Whenever possible, use magnetic field isolation
equipment such as a Helmholtz field to surround
the monitor. If a Helmholtz field is not available,
frequently degauss the unit under test.
Caution:
Other electrical equipment may cause
external magnetic fields which may
interfere with monitor performance.
Use an external degaussing coil to limit magnetic
build up on the monitor. If an external degaussing
coil is not available, use the internal degaussing
circuit. However, do not use the internal
degaussing circuit more than once per 30 minutes.
4-1-1 (c) WARM-UP TIME
The monitor must be on for 30 minutes before
starting alignment. Warm-up time is especially
critical in color temperature and white balance
adjustments.
4-1-1 (d) SIGNAL
Analog, 0.7 Vp-p positive at 75 ohm, internal
termination
Sync: Separate/Composite
(TTL level negative/positive)
Sync-on-Green:
Composite sync 0.3 Vp-p negative
(Video 0.7 Vp-p positive)
4-1-1 (e) SCANNING FREQUENCY
Horizontal: 30 kHz to 115 kHz (Automatic)
Vertical:
50 Hz to 160 Hz (Automatic)
Unless otherwise specified, adjust at the
1024 x 768 mode (H: 68 kHz, V: 85 Hz) signals.
Refer to Table 2-1 on pages 2-2 and 2-3.
4-1-1 (f) HIGH VOLTAGE ADJUSTMENT
Signal:
Display image: Full white
Contrast:
Brightness:
Limit:
1024 x 768 mode (68 kHz/85 Hz)
Maximum
Maximum
27.3 kV ± 0.5 kV
(17ó: 26 kV ± 0.5 kV)
Measure the hight voltage level at the anode cap.
High voltage should be within the limit as above.
If the high voltage needs adjustment use the
Softjig.
4-1-1 (g) G2 (SCREEN) VOLTAGE ADJUSTMENT
Signal:
1024 x 768 mode (68 kHz/85 Hz)
Display image: Full white
Contrast:
Maximum
Brightness:
Maximum
Adjust the Screen VR of the FBT so that the G2
(Screen) Voltage for Toshiba it is 540 V ± 10 V.
4-1-1 (h) CENTER RASTER
Adjust VR401 so that the back raster comes to the
center when you apply a signal of 91 kHz/85 Hz.
PG17**/PG19**/PG21**
4-1
4 Alignment and Adjustments
This section of the service manual explains how to make permanent adjustments to the monitor. Direction
is given for adjustment using the monitor Interface Board Ver. 2.0 and software (Softjig).
4-1 Adjustment Conditions
Caution:
Changes made without the Softjig are saved only to the user mode settings. As such, the
settings are not permanently stored and may be inadvertently deleted by the user.
PG17H*
SDD
TOSHIBA
G2
525V
635V
PG19S*
PG19R*
G2
560V
530V
MEC
SDD
相關PDF資料
PDF描述
PG19LO Monitor_ICs:88P6232 7045 SAM9222G PG17/19 TNY254P 52748 KS2501B-10 KA2507
PG19LS Monitor_ICs:88P6232 7045 SAM9222G PG17/19 TNY254P 52748 KS2501B-10 KA2507
PG19R* Monitor_ICs:88P6232 7045 SAM9222G PG17/19 TNY254P 52748 KS2501B-10 KA2507
PG19S* Monitor_ICs:88P6232 7045 SAM9222G PG17/19 TNY254P 52748 KS2501B-10 KA2507
PG21* Dual 100mA/500mA Low Dropout, Low Noise, Micropower Regulator; Package: DFN; No of Pins: 12; Temperature Range: -40°C to +125°C
相關代理商/技術參數
參數描述
PG19LO 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Monitor_ICs:88P6232 7045 SAM9222G PG17/19 TNY254P 52748 KS2501B-10 KA2507
PG19LS 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Monitor_ICs:88P6232 7045 SAM9222G PG17/19 TNY254P 52748 KS2501B-10 KA2507
PG1A05HW 制造商:Aleph America Corporation 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*