參數(shù)資料
型號: PG17H*
英文描述: High Voltage 1.5A, 500kHz Step-Down Switching Regulator with 100µA Quiescent Current; Package: TSSOP; No of Pins: 16; Temperature Range: -40°C to +85°C
中文描述: Monitor_ICs:88P6232 7045 SAM9222G PG17/19 TNY254P 52748 KS2501B - 10 KA2507
文件頁數(shù): 10/100頁
文件大小: 3595K
4-1-1 (i) BRIGHTNESS AND CONTRAST
Unless otherwise specified, adjust control
volumes:
Brightness: Maximum
Contrast:
Maximum
4-1-2 Required Equipment
The following equipment may be necessary for
adjustment procedures:
4-1-2 (a) DISPLAY CONTROL ADJUSTMENT
1.
Non-metallic (D) screwdriver: 1.5 mm
Non-metallic (D) screwdriver: 3 mm
2.
Philips (+) screwdriver: 1.5 mm
3.
Non-metallic hexkey: 2.5 mm
4.
Digital Multimeter (DMM), or
Digital Voltmeter (DVM)
5.
Signal generator, or
Computer with a video board that uses the
ET-4000 chipset (strongly recommended if
using Samsung DM 200 software) and that
displays: 1280 x 1024 @ 85 Hz, or 1600 x 1200
@ 85 Hz (maximum).
6.
Personal computer
7.
Required software: Softjig.exe from Samsung
which includes the SF9839TE.MDL
(Toshiba CRT) data file
Samsung DM200, or DisplayMate for
Windows from Sonera Technologies
8.
Interface Board Ver. 2.0 Code No.
BH81-90001K
9.
Parallel communications cable (25-pin to
25-pin); Code No. BH81-90001H
10. Signal cable (15-pin to 15-pin cable with
additional 3-pin connector); Code No.
BH81-90001J
11. 5 V DC adapter, not supplied
Note:
Softjig Assy (includes items 8, 9 and 10)
Code No. BH81-90001L
4-1-2 (b) COLOR ADJUSTMENTS
1.
All equipment listed in 4-1-2 (a), above
2.
Color analyzer, or any luminance
measurement equipmen
4-1-3
Connecting the SoftJig
Connect the monitor to the signal generator and/
or PC as illustrated in Figures 4-1 and 4-2.
Note:
The signal cable connector which includes
the 3-wire cable must connect to the
monitor. If you use Setup 2 (PC only, no
signal generator) you can only make
adjustments to the signal timing available
on that computer system. To make
corrections to all factory timings requires
the use of an additional signal generator.
4-1-4
After Making Adjustments
After finishing all adjustments, test the monitor in
all directions. If, for example, the monitor does not
meet adjustment specifications when facing north,
reposition the monitor to face east and readjust.
This time, try for an adjustment closer to the ideal
setting within the tolerance range. Test the unit
again in all directions. If the monitor again fails to
meet specifications in every direction, contact
your Regional After Service Center for possible
CRT replacement.
4 Alignment and Adjustments
4-2
PG17**/PG19**/PG21**
MONITOR
INTERFACE
BOARD VER. 2.0
PC
SIGNAL
GENERATOR
3-WIRE
CABLE
SIGNAL CABLE
5V DC
ADAPTOR
PARALLEL CABLE
Figure 4-1. Setup 1, With Signal Generator
MONITOR
INTERFACE
BOARD VER. 2.0
PC
3-WIRE CABLE
SIGNAL CABLE
PARALLEL CABLE
D-SUB
CONNECTOR
5V DC
ADAPTOR
Figure 4-2. Setup 2, Without Signal Generator
相關PDF資料
PDF描述
PG17IS Monitor_ICs:88P6232 7045 SAM9222G PG17/19 TNY254P 52748 KS2501B-10 KA2507
PG19HS Monitor_ICs:88P6232 7045 SAM9222G PG17/19 TNY254P 52748 KS2501B-10 KA2507
PG19IS Monitor_ICs:88P6232 7045 SAM9222G PG17/19 TNY254P 52748 KS2501B-10 KA2507
PG19LO Monitor_ICs:88P6232 7045 SAM9222G PG17/19 TNY254P 52748 KS2501B-10 KA2507
PG19LS Monitor_ICs:88P6232 7045 SAM9222G PG17/19 TNY254P 52748 KS2501B-10 KA2507
相關代理商/技術參數(shù)
參數(shù)描述
PG188/PG185 制造商:Shure 功能描述:Performance Gear UHF Wireless Dual Channel Lavalier Microphone System
PG188/PG185=-H7 制造商:Shure 功能描述:Includes PG88 Dual Channel Diversity Receiver, Two PG1 Bodypack Transmitter, and
PG188/PG185=-K7 制造商:Shure 功能描述:Includes PG88 Dual Channel Diversity Receiver, Two PG1 Bodypack Transmitter, and
PG188/PG185=-M7 制造商:Shure 功能描述:Includes PG88 Dual Channel Diversity Receiver, Two PG1 Bodypack Transmitter, and
PG1910 制造商:OHIO BUCKEYE 功能描述: