- 您現在的位置：買賣IC網 > PDF目錄369995 > PF48F4P0ZBQ0 (Intel Corp.) Intel StrataFlash Embedded Memory PDF資料下載
參數資料
| 型號： | PF48F4P0ZBQ0 |
| 廠商： | Intel Corp. |
| 英文描述： | Intel StrataFlash Embedded Memory |
| 中文描述： | 英特爾StrataFlash嵌入式存儲器 |
| 文件頁數： | 65/102頁 |
| 文件大?。?/td> | 1609K |
| 代理商： | PF48F4P0ZBQ0 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁當前第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁
1-Gbit P30 Family
Datasheet
Intel StrataFlash
Embedded Memory (P30)
Order Number: 306666, Revision: 001
April 2005
65
Two basic sequences repeat in this phase: loading of the write buffer, followed by buffer data
programming to the array. For BEFP, the count value for buffer loading is always the maximum
buffer size of 32 words. During the buffer-loading sequence, data is stored to sequential buffer
locations starting at address 0x00. Programming of the buffer contents to the flash memory array
starts as soon as the buffer is full. If the number of words is less than 32, the remaining buffer
locations must be filled with 0xFFFF.
Caution:
The buffer must be completely filled for programming to occur. Supplying an address outside of the
current block's range during a buffer-fill sequence causes the algorithm to exit immediately. Any
data previously loaded into the buffer during the fill cycle is not programmed into the array.
The starting address for data entry must be buffer size aligned, if not the BEFP algorithm will be
aborted and the program fails and (SR[4]) flag will be set.
Data words from the write buffer are directed to sequential memory locations in the flash memory
array; programming continues from where the previous buffer sequence ended. The host
programming system must poll SR[0] to determine when the buffer program sequence completes.
SR[0] cleared indicates that all buffer data has been transferred to the flash array; SR[0] set
indicates that the buffer is not available yet for the next fill cycle. The host system may check full
status for errors at any time, but it is only necessary on a block basis after BEFP exit. After the
buffer fill cycle, no write cycles should be issued to the device until SR[0] = 0 and the device is
ready for the next buffer fill.
Note:
Any spurious writes are ignored after a buffer fill operation and when internal program is
proceeding.
The host programming system continues the BEFP algorithm by providing the next group of data
words to be written to the buffer. Alternatively, it can terminate this phase by changing the block
address to one outside of the current block’s range.
The Program/Verify phase concludes when the programmer writes to a different block address;
data supplied must be 0xFFFF. Upon Program/Verify phase completion, the device enters the
BEFP Exit phase.
11.3.4
BEFP Exit Phase
When SR[7] is set, the device has returned to normal operating conditions. A full status check
should be performed at this time to ensure the entire block programmed successfully. When exiting
the BEFP algorithm with a block address change, the read mode will not change. After BEFP exit,
any valid command can be issued to the device.
11.4
Program Suspend
Issuing the Program Suspend command while programming suspends the programming operation.
This allows data to be accessed from the device other than the one being programmed. The
Program Suspend command can be issued to any device address. A program operation can be
suspended to perform reads only. Additionally, a program operation that is running during an erase
suspend can be suspended to perform a read operation (see
Figure 41, “Program Suspend/Resume
Flowchart” on page 86
).
相關PDF資料 |
PDF描述 |
|---|---|
| PF48F4P0VB00 | Photoelectric Sensor; Sensor Input Type:Optical; Sensing Range Max:43mm; Sensor Output Type:Relay; Leaded Process Compatible:No; Output Type:Relay; Peak Reflow Compatible (260 C):No; Contact Current Max:3A; Contact Rating:3A |
| PF48F0P0VT00 | Intel StrataFlash Embedded Memory |
| PF48F2P0VT00 | Intel StrataFlash Embedded Memory |
| PF48F3P0VT00 | Intel StrataFlash Embedded Memory |
| PF48F4P0VT00 | Intel StrataFlash Embedded Memory |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PF48F4P0ZT00 | 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:Intel StrataFlash Embedded Memory |
| PF48F4P0ZTQ0 | 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:Intel StrataFlash Embedded Memory |
| PF48F5000M0Y1BEA | 制造商:Micron Technology Inc 功能描述:512BA/0S SCSP 1.8 X16D HF B1 ADMUX - Trays |
| PF48F6000M0Y0BEA | 制造商:Micron Technology Inc 功能描述:1024CP/0CP SCSP 1.8 X16D LF - Trays |
| PF48F6000M0Y0BHA | 制造商:Micron Technology Inc 功能描述:WIRELESS - Trays |
發布緊急采購，3分鐘左右您將得到回復。