參數資料
型號： PF48F3000P0ZTQ0
廠商： INTEL CORP
元件分類： PROM
英文描述： Circular Connector; Body Material:Aluminum; Series:PT00; No. of Contacts:6; Connector Shell Size:10; Connecting Termination:Solder; Circular Shell Style:Wall Mount Receptacle; Circular Contact Gender:Pin; Insert Arrangement:10-6
中文描述： 8M X 16 FLASH 1.8V PROM, 85 ns, PBGA88
封裝： 8 X 10 MM, 1.20 MM HEIGHT, LEAD FREE, SCSP-88
文件頁數： 62/102頁
文件大小： 1609K
代理商： PF48F3000P0ZTQ0
1-Gbit P30 Family
April 2005
62
Intel StrataFlash
Embedded Memory (P30)
Order Number: 306666, Revision: 001
Datasheet
During programming, the Write State Machine (WSM) executes a sequence of internally-timed
events that program the desired data bits at the addressed location, and verifies that the bits are
sufficiently programmed. Programming the flash memory array changes “ones” to “zeros”.
Memory array bits that are zeros can be changed to ones only by erasing the block (see
Section
12.0, “Erase Operations” on page 67
).
The Status Register can be examined for programming progress and errors by reading at any
address. The device remains in the Read Status Register state until another command is written to
the device.
Status Register bit SR[7] indicates the programming status while the sequence executes.
Commands that can be issued to the device during programming are Program Suspend, Read Status
Register, Read Device Identifier, CFI Query, and Read Array (this returns unknown data).
When programming has finished, Status Register bit SR[4] (when set) indicates a programming
failure. If SR[3] is set, the WSM could not perform the word programming operation because V
PP
was outside of its acceptable limits. If SR[1] is set, the word programming operation attempted to
program a locked block, causing the operation to abort.
Before issuing a new command, the Status Register contents should be examined and then cleared
using the Clear Status Register command. Any valid command can follow, when word
programming has completed.
11.1.1
Factory Word Programming
Factory word programming is similar to word programming in that it uses the same commands and
programming algorithms. However, factory word programming enhances the programming
performance with V
PP
= V
PPH
. This can enable faster programming times during OEM
manufacturing processes. Factory word programming is not intended for extended use. See
Section
5.2, “Operating Conditions” on page 30
for limitations when V
PP
= V
PPH
.
Note:
When V
PP
= V
PPL
, the device draws programming current from the V
CC
supply. If V
PP
is driven
by a logic signal, V
PPL
must remain above V
PPL
MIN to program the device. When V
PP
= V
PPH
,
the device draws programming current from the V
PP
supply.
Figure 31, “Example VPP Supply
Connections” on page 66
shows examples of device power supply configurations.
11.2
Buffered Programming
The device features a 32-word buffer to enable optimum programming performance. For Buffered
Programming, data is first written to an on-chip write buffer. Then the buffer data is programmed
into the flash memory array in buffer-size increments. This can improve system programming
performance significantly over non-buffered programming.
When the Buffered Programming Setup command is issued (see
Section 9.2, “Device Commands”
on page 50
), Status Register information is updated and reflects the availability of the buffer. SR[7]
indicates buffer availability: if set, the buffer is available; if cleared, the buffer is not available. To
retry, issue the Buffered Programming Setup command again, and re-check SR[7]. When SR[7] is
set, the buffer is ready for loading. (see
Figure 42, “Buffer Program Flowchart” on page 87
).
On the next write, a word count is written to the device at the buffer address. This tells the device
how many data words will be written to the buffer, up to the maximum size of the buffer.
相關PDF資料
PDF描述
PF48F4000P0ZTQ0 Circular Connector; MIL SPEC:MIL-C-26482, Series I, Solder; Body Material:Aluminum; Series:PT00; Number of Contacts:6; Connector Shell Size:10; Connecting Termination:Solder; Circular Shell Style:Wall Mount Receptacle
PF48F0P0ZTQ0 Circular Connector; Body Material:Aluminum; Series:PT00; No. of Contacts:6; Connector Shell Size:10; Connecting Termination:Solder; Circular Shell Style:Wall Mount Receptacle; Circular Contact Gender:Socket; Insert Arrangement:10-98
PF48F2P0ZTQ0 Circular Connector; MIL SPEC:MIL-C-26482, Series I, Solder; Body Material:Aluminum; Series:PT00; No. of Contacts:10; Connector Shell Size:12; Connecting Termination:Solder; Circular Shell Style:Wall Mount Receptacle
PF48F3P0ZTQ0 Circular Connector; Body Material:Aluminum; Series:PT00; No. of Contacts:10; Connector Shell Size:12; Connecting Termination:Solder; Circular Shell Style:Wall Mount Receptacle; Circular Contact Gender:Pin; Insert Arrangement:12-10
PF48F4P0ZTQ0 Circular Connector; MIL SPEC:MIL-C-26482, Series I, Solder; Body Material:Aluminum; Series:PT00; No. of Contacts:10; Connector Shell Size:12; Connecting Termination:Solder; Circular Shell Style:Wall Mount Receptacle
相關代理商/技術參數
參數描述
PF48F3000P0ZTQ0A 功能描述:IC FLASH 128MBIT 85NS 88TPBGA RoHS:是 類別:集成電路 (IC) >> 存儲器 系列:StrataFlash™ 標準包裝:1 系列:- 格式 - 存儲器:閃存 存儲器類型:閃存 - NAND 存儲容量:4G（256M x 16） 速度:- 接口:并聯 電源電壓:2.7 V ~ 3.6 V 工作溫度:0°C ~ 70°C 封裝/外殼:48-TFSOP（0.724"，18.40mm 寬） 供應商設備封裝:48-TSOP I 包裝:Digi-Reel® 其它名稱:557-1461-6
PF48F3000P0ZTQEA 功能描述:IC FLASH 128MBIT 65NM SCSP RoHS:是 類別:集成電路 (IC) >> 存儲器 系列:Axcell™ 標準包裝:1 系列:- 格式 - 存儲器:閃存 存儲器類型:閃存 - NAND 存儲容量:4G（256M x 16） 速度:- 接口:并聯 電源電壓:2.7 V ~ 3.6 V 工作溫度:0°C ~ 70°C 封裝/外殼:48-TFSOP（0.724"，18.40mm 寬） 供應商設備封裝:48-TSOP I 包裝:Digi-Reel® 其它名稱:557-1461-6
PF48F3P0VB00 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:Intel StrataFlash Embedded Memory
PF48F3P0VBQ0 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:Intel StrataFlash Embedded Memory
PF48F3P0VT00 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:Intel StrataFlash Embedded Memory
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*