參數資料
型號: PCA9674TS,118
廠商: NXP Semiconductors
文件頁數: 9/40頁
文件大?。?/td> 0K
描述: IC I/O EXPANDER I2C 8B 20SSOP
產品培訓模塊: LED Controllers
標準包裝: 1
接口: I²C
輸入/輸出數: 8
中斷輸出:
頻率 - 時鐘: 1MHz
電源電壓: 2.3 V ~ 5.5 V
工作溫度: -40°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: 20-LSSOP(0.173",4.40mm 寬)
供應商設備封裝: 20-SSOP
包裝: 標準包裝
包括: POR
其它名稱: 568-4078-6
PCA9674_PCA9674A
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2013. All rights reserved.
Product data sheet
Rev. 7 — 30 May 2013
17 of 40
NXP Semiconductors
PCA9674; PCA9674A
Remote 8-bit I/O expander for Fm+ I2C-bus with interrupt
8.4 Power-on reset
When power is applied to VDD, an internal Power-On Reset (POR) holds the PCA9674;
PCA9674A in a reset condition until VDD has reached VPOR. At that point, the reset
condition is released and the PCA9674; PCA9674A registers and I2C-bus/SMBus state
machine will initialize to their default states of all I/O inputs with weak current source to
VDD. Thereafter VDD must be lowered below VPOR and back up to the operation voltage for
power-on reset cycle.
8.5 Interrupt output (INT)
The PCA9674/74A provides an open-drain output (INT) which can be fed to a
corresponding input of the microcontroller (see Figure 15). As soon as a port input is
changed, the INT will be active (LOW) and notify the microcontroller.
An interrupt is generated at any rising or falling edge of the port inputs. After time tv(Q), the
signal INT is valid.
The interrupt will reset to HIGH when data on the port is changed to the original setting or
data is read or written by the master.
In the Write mode, the interrupt may become de-activated (HIGH) on the rising edge of
the acknowledge bit of the data byte and also on the rising edge of the write to port pulse.
The interrupt will always be reset (HIGH) on the falling edge of the write to port pulse (see
The interrupt is reset (HIGH) in the Read mode on the rising edge of the acknowledge of
slave address byte and on the rising edge of the read from port pulse (see Figure 14).
During the interrupt reset, any I/O change close to the read or write pulse may not
generate an interrupt, or the interrupt will have a very short pulse. After the interrupt is
reset, any change in I/Os will be detected and transmitted as an INT.
At power-on reset all ports are in Input mode and the initial state of the ports is HIGH,
therefore, for any port pin that is pulled LOW or driven LOW by external source, the
interrupt output will be active (output LOW).
Fig 15. Application of multiple PCA9674s with interrupt
002aac122
VDD
MICROCOMPUTER
INT
PCA9674
INT
PCA9674
INT
device 1
device 2
PCA9674
INT
device 8
相關PDF資料
PDF描述
PCA9674ATS,118 IC I/O EXPANDER I2C 8B 20SSOP
PCA9674PW,112 IC I/O EXPANDER I2C 8B 16TSSOP
PCA9554D,118 IC I/O EXPANDER I2C 8B 16SOIC
PCA9554ATS,112 IC I/O EXPANDER I2C 8B 20SSOP
PCA9554AD,118 IC I/O EXPANDER I2C 8B 16SOIC
相關代理商/技術參數
參數描述
PCA9674TS-T 功能描述:接口-I/O擴展器 8-BIT I2C FM+ QB GPIO RST PU RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel
PCA9675BQ,118 功能描述:接口-I/O擴展器 REMOTE 16BIT GPIO RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel
PCA9675BQ-T 功能描述:接口-I/O擴展器 REMOTE 16BIT GPIO FM+I2C-INTER RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel
PCA9675BS,118 功能描述:接口-I/O擴展器 16-BIT I2C FM+ QB RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel
PCA9675BS-T 功能描述:接口-I/O擴展器 16-BIT I2C FM+ QB GPIO RST PU RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel