參數資料
型號: PCA9674APW,118
廠商: NXP Semiconductors
文件頁數: 3/40頁
文件大?。?/td> 0K
描述: IC I/O EXPANDER I2C 8B 16TSSOP
產品培訓模塊: LED Controllers
特色產品: NXP - I2C Interface
標準包裝: 1
接口: I²C
輸入/輸出數: 8
中斷輸出:
頻率 - 時鐘: 1MHz
電源電壓: 2.3 V ~ 5.5 V
工作溫度: -40°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: 16-TSSOP(0.173",4.40mm 寬)
供應商設備封裝: 16-TSSOP
包裝: 標準包裝
包括: POR
其它名稱: 568-4073-6
PCA9674_PCA9674A
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2013. All rights reserved.
Product data sheet
Rev. 7 — 30 May 2013
11 of 40
NXP Semiconductors
PCA9674; PCA9674A
Remote 8-bit I/O expander for Fm+ I2C-bus with interrupt
7.2 Software Reset Call, and device ID addresses
Two other different addresses can be sent to the PCA9674; PCA9674A.
General Call address: allows to reset the PCA9674; PCA9674A through the I2C-bus
upon reception of the right I2C-bus sequence. See Section 7.2.1 “Software Reset” for
more information.
Device ID address: allows to read ID information from the device (manufacturer, part
for more information.
7.2.1 Software Reset
The Software Reset Call allows all the devices in the I2C-bus to be reset to the power-up
state value through a specific formatted I2C-bus command. To be performed correctly, it
implies that the I2C-bus is functional and that there is no device hanging the bus.
The Software Reset sequence is defined as following:
1. A START command is sent by the I2C-bus master.
2. The reserved General Call I2C-bus address ‘0000 000’ with the R/W bit set to 0 (write)
is sent by the I2C-bus master.
3. The PCA9674; PCA9674A device(s) acknowledge(s) after seeing the General Call
address ‘0000 0000’ (00h) only. If the R/W bit is set to 1 (read), no acknowledge is
returned to the I2C-bus master.
4. Once the General Call address has been sent and acknowledged, the master sends
1 byte. The value of the byte must be equal to 06h.
a. The PCA9674; PCA9674A acknowledges this value only. If the byte is not equal to
06h, the PCA9674; PCA9674A does not acknowledge it.
If more than 1 byte of data is sent, the PCA9674; PCA9674A does not acknowledge
any more.
5. Once the right byte has been sent and correctly acknowledged, the master sends a
STOP command to end the Software Reset sequence: the PCA9674; PCA9674A
then resets to the default value (power-up value) and is ready to be addressed again
within the specified bus free time. If the master sends a Repeated START instead, no
reset is performed.
Fig 7.
General Call address
Fig 8.
Device ID address
0
002aac115
0
R/W
002aac116
1
0
相關PDF資料
PDF描述
PCA9672PW,112 IC I/O EXPANDER I2C 8B 16TSSOP
PCA9574PW,112 IC I/O EXPANDER I2C 8B 16TSSOP
PCA9574PW,118 IC I/O EXPANDER I2C 8B 16TSSOP
2-964577-2 MULTIFIT RAHMEN 2P
1-964577-5 MULTIFIT RAHMEN 5P
相關代理商/技術參數
參數描述
PCA9674APW-T 功能描述:接口-I/O擴展器 8-BIT I2C FM+ QB GPIO INT PU RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel
PCA9674ATS 功能描述:接口-I/O擴展器 8-BIT I2C FM+ QB GPIO RST PU RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel
PCA9674ATS,112 功能描述:接口-I/O擴展器 8-BIT I2C FM+ QB RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel
PCA9674ATS,118 功能描述:接口-I/O擴展器 8-BIT I2C FM+ QB RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel
PCA9674ATS-T 功能描述:接口-I/O擴展器 8-BIT I2C FM+ QB GPIO INT PU RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel