- 您現在的位置：買賣IC網 > PDF目錄367809 > PCA9557 (NXP Semiconductors N.V.) 8-bit I2C and SMBus I/0 port with reset PDF資料下載
參數資料
| 型號： | PCA9557 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | 8-bit I2C and SMBus I/0 port with reset |
| 中文描述： | 8位I2C和SMBus I / 0端口復位 |
| 文件頁數： | 6/16頁 |
| 文件大?。?/td> | 127K |
| 代理商： | PCA9557 |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁
Philips Semiconductors
Product data
PCA9557
8-bit I
2
C and SMBus I/0 port with reset
2001 Dec 12
6
DEVICE ADDRESS
Following a START condition the bus master must output the
address of the slave it is accessing. The address of the PCA9557 is
shown in Figure 6. To conserve power, no internal pullup resistors
are incorporated on the hardware selectable address pins and they
must be pulled HIGH or LOW.
0
0
1
1
A2
A1
A0
slave address
su01048
fixed
programmable
R/W
Figure 6. PCA9557 address
The last bit of the slave address defines the operation to be
performed. When set to logic 1 a read is selected while a logic 0
selects a write operation.
CONTROL REGISTER
Following the successful acknowledgement of the slave address,
the bus master will send a byte to the PCA9557, which will be stored
in the control register. This register can be written and read via the
I
2
C bus.
0
0
0
0
D1
D0
0
SW00953
0
Figure 7. Control Register
REGISTER DEFINITION
D1
D0
NAME
TYPE
FUNCTION
0
0
Register 0
Read
Input port register
0
1
Register 1
Read/Write
Output port register
1
0
Register 2
Read/Write
Polarity inversion
register
1
1
Register 3
Read/Write
Configuration
register
REGISTER DESCRIPTION
Register 0 – Input Port Register
I7
I6
I5
I4
I3
I2
I1
I0
This register is an read-only port. It reflects the incoming logic levels
of the pins, regardless of whether the pin is defined as an input or an
output by the Configuration Register. Writes to this register have no
effect.
Register 1 – Output Port Register
bit
O7
O6
O5
O4
O3
O2
O1
O0
default
0
0
0
0
0
0
0
0
This register reflects the outgoing logic levels of the pins defined as
outputs by the Configuration Register. Bit values in this register have
no effect on pins defined as inputs. In turn, reads from this register
reflect the value that is in the flip-flop controlling the output selection,
NOT the actual pin value.
Register 2 – Polarity Inversion Register
bit
N7
N6
N5
N4
N3
N2
N1
N0
default
1
1
1
1
0
0
0
0
This register enables polarity inversion of pins defined as inputs by
the Configuration Register. If a bit in this register is set (written
with ‘1’), the corresponding port pin’s polarity is inverted. If a bit in
this register is cleared (written with a ‘0’), the corresponding port
pin’s original polarity is retained.
Register 3 – Configuration Register
bit
C7
C6
C5
C4
C3
C2
C1
C0
default
1
1
1
1
1
1
1
1
This register configures the directions of the I/O pins. If a bit in this
register is set, the corresponding port pin is enabled as an input with
high impedance output driver. If a bit in this register is cleared, the
corresponding port pin is enabled as an output.
POWER-ON RESET
When power is applied to V
DD
, an internal power-on reset holds the
PCA9557 in a reset state until V
DD
has reached V
POR
. At that point,
the reset condition is released and the PCA9557 registers and
I
2
C/SMBus state machine will initialize to their default states.
For a power reset cycle, V
DD
must be set to 0 V, then ramped back
to the operating voltage.
RESET INPUT
A reset can be accomplished by holding the RESET pin LOW for a
minimum of t
W
. The PCA9557 registers and SMBus/I
2
C state
machine will be held in their default state until the RESET input is
once again HIGH. This input typically requires a pull-up to V
CC.
相關PDF資料 |
PDF描述 |
|---|---|
| PCA9558 | 8-bit I2C and SMBus I/O port with 5-bit multiplexed/1-bit latched 6-bit I2C EEPROM and 2 k bit EEPROM |
| PCA9559 | 5-bit multiplexed/1-bit latched 6-bit I I C EEPROM(5位多路的/1位鎖存的6位IIC EEPROM) |
| PCA9564 | Parallel bus to I2C-bus controller |
| PCA9665 | Fm+ parallel bus to I2C-bus controller |
| PCA9665N | Fm+ parallel bus to I2C-bus controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PCA9557BS | 制造商:NXP Semiconductors 功能描述: |
| PCA9557BS,118 | 功能描述:接口-I/O擴展器 8-BIT I2C FM TP GPIO RST RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel |
| PCA9557D | 功能描述:接口-I/O擴展器 Remote 8B I2C & SMBus I/O Expander RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel |
| PCA9557D,112 | 功能描述:接口-I/O擴展器 OCT SMBUS/I2C INTRFC RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel |
| PCA9557D,118 | 功能描述:接口-I/O擴展器 8-BIT I2C FM TP GPIO RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。