- 您現在的位置：買賣IC網 > PDF目錄367809 > PCA9544PWDH (NXP SEMICONDUCTORS) 4-channel I2C multiplexer and interrupt controller PDF資料下載
參數資料
| 型號： | PCA9544PWDH |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 4-channel I2C multiplexer and interrupt controller |
| 中文描述： | 4 CHANNEL(S), I2C BUS CONTROLLER, PDSO20 |
| 封裝： | 4.40 MM, PLASTIC, TSSOP-20 |
| 文件頁數： | 5/12頁 |
| 文件大?。?/td> | 77K |
| 代理商： | PCA9544PWDH |
Philips Semiconductors
Product specification
PCA9544
4-channel I
2
C multiplexer and interrupt controller
1999 Oct 07
5
CHARACTERISTICS OF THE I
2
C-BUS
The I
2
C-bus is for 2-way, 2-line communication between different ICs
or modules. The two lines are a serial data line (SDA) and a serial
clock line (SCL). Both lines must be connected to a positive supply
via a pull-up resistor when connected to the output stages of a device.
Data transfer may be initiated only when the bus is not busy.
Bit transfer
One data bit is transferred during each clock pulse. The data on the
SDA line must remain stable during the HIGH period of the clock
pulse as changes in the data line at this time will be interpreted as
control signals (see FIgure 1).
SDA
SCL
SW00363
data line
stable;
data valid
change
of data
allowed
Figure 1. Bit transfer
Start and stop conditions
Both data and clock lines remain HIGH when the bus is not busy. A
HIGH-to-LOW transition of the data line, while the clock is HIGH is
defined as the start condition (S). A LOW-to-HIGH transition of the
data line while the clock is HIGH is defined as the stop condition (P)
(see Figure 2).
System configuration
A device generating a message is a ‘transmitter’, a device receiving
is the ‘receiver’. The device that controls the message is the
‘master’ and the devices which are controlled by the master are the
‘slaves’ (see Figure 3).
SDA
SCL
SW00365
S
P
SDA
SCL
START condition
STOP condition
Figure 2. Definition of start and stop conditions
MASTER
TRANSMITTER/
RECEIVER
SLAVE
RECEIVER
SLAVE
TRANSMITTER/
RECEIVER
MASTER
TRANSMITTER
MASTER
TRANSMITTER/
RECEIVER
SDA
SCL
SW00366
I
2
C
MULTIPLEXER
SLAVE
Figure 3. System configuration
相關PDF資料 |
PDF描述 |
|---|---|
| PCA9544PW | 4-channel I2C multiplexer and interrupt controller |
| PCA9544 | 4-channel IIC multiplexer and interrupt controller(4通道IIC多路復用器和中斷控制器) |
| PCA9546A | 4-channel I2C switch with reset |
| PCA9546 | 4-channel I2C switch with reset |
| PCA9546D | 4-channel I2C switch with reset |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PCA9545 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:4-channel I2C switch with interrupt logic and reset |
| PCA9545A | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:4-channel I2C-bus switch with interrupt logic and reset |
| PCA9545ABS | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:4-channel I2C-bus switch with interrupt logic and reset |
| PCA9545ABS,118 | 功能描述:多路器開關 IC I2C SWITCH 4CH RoHS:否 制造商:Texas Instruments 通道數量:1 開關數量:4 開啟電阻（最大值）:7 Ohms 開啟時間（最大值）: 關閉時間（最大值）: 傳播延遲時間:0.25 ns 工作電源電壓:2.3 V to 3.6 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UQFN-16 |
| PCA9545ABS-T | 功能描述:多路器開關 IC I2C SWITCH 4CH RoHS:否 制造商:Texas Instruments 通道數量:1 開關數量:4 開啟電阻（最大值）:7 Ohms 開啟時間（最大值）: 關閉時間（最大值）: 傳播延遲時間:0.25 ns 工作電源電壓:2.3 V to 3.6 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UQFN-16 |
發布緊急采購，3分鐘左右您將得到回復。