- 您現在的位置：買賣IC網 > PDF目錄367809 > PCA9544 (NXP Semiconductors N.V.) 4-channel IIC multiplexer and interrupt controller(4通道IIC多路復用器和中斷控制器) PDF資料下載
參數資料
| 型號： | PCA9544 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | 4-channel IIC multiplexer and interrupt controller(4通道IIC多路復用器和中斷控制器) |
| 中文描述： | 4通道復用器和國際進口中斷控制器（4通道進口證多路復用器和中斷控制器） |
| 文件頁數： | 6/12頁 |
| 文件大?。?/td> | 77K |
| 代理商： | PCA9544 |
Philips Semiconductors
Product specification
PCA9544
4-channel I
2
C multiplexer and interrupt controller
1999 Oct 07
6
Acknowledge
The number of data bytes transferred between the start and the stop conditions from transmitter to receiver is not limited. Each byte of eight bits
is followed by one acknowledge bit. The acknowledge bit is a HIGH level put on the bus by the transmitter whereas the master generates an
extra acknowledge related clock pulse.
A slave receiver which is addressed must generate an acknowledge after the reception of each byte. Also a master must generate an
acknowledge after the reception of each byte that has been clocked out of the slave transmitter. The device that acknowledges has to pull down
the SDA line during the acknowledge clock pulse, so that the SDA line is stable LOW during the HIGH period of the acknowledge related clock
pulse, set-up and hold times must be taken into account.
A master receiver must signal an end of data to the transmitter by not generating an acknowledge on the last byte that has been clocked out of
the slave. In this event, the transmitter must leave the data line HIGH to enable the master to generate a stop condition.
DATA OUTPUT
BY TRANSMITTER
SCL FROM
MASTER
SW00368
DATA OUTPUT
BY RECEIVER
1
2
8
9
S
START condition
clock pulse for
acknowledgement
acknowledge
not acknowledge
Figure 4. Acknowledgement on the I
2
C-bus
1
1
0
A2
A1 A0
slave address
fixed
hardware selectable
SW00453
1
Figure 5. Slave address
相關PDF資料 |
PDF描述 |
|---|---|
| PCA9546A | 4-channel I2C switch with reset |
| PCA9546 | 4-channel I2C switch with reset |
| PCA9546D | 4-channel I2C switch with reset |
| PCA9546PW | 4-channel I2C switch with reset |
| PCA9549 | Octal bus switch with individually I2C-bus controlled enables |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PCA9544A | 制造商:TI 制造商全稱:Texas Instruments 功能描述:4-CHANNEL I2C AND SMBus MULTIPLEXER WITH INTERRUPT LOGIC |
| PCA9544A_07 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:4-CHANNEL I2C AND SMBus MULTIPLEXER WITH INTERRUPT LOGIC |
| PCA9544A_09 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:4-channel I2C-bus multiplexer with interrupt logic |
| PCA9544ABS | 制造商:NXP Semiconductors 功能描述: |
| PCA9544ABS,118 | 功能描述:多路器開關 IC 4-CH I2C MUX W/INTERRUPT RoHS:否 制造商:Texas Instruments 通道數量:1 開關數量:4 開啟電阻（最大值）:7 Ohms 開啟時間（最大值）: 關閉時間（最大值）: 傳播延遲時間:0.25 ns 工作電源電壓:2.3 V to 3.6 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UQFN-16 |
發布緊急采購，3分鐘左右您將得到回復。